Instrukcja obsługi EverFocus ECD900B
EverFocus
Kamera monitorująca
ECD900B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla EverFocus ECD900B (18 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 4.5 użytkowników na średnio 4.5 gwiazdek
Strona 1/18

EHD935 eZ.HD Series
720p Analog High Denion
True Day/Night Outdoor IR Dome Vandal Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: Nov., 2014

2
Precauons
1. Do not install the camera near electric or magnec elds. Install the camera away from
TV/radio transmiers, magnets, electric motors, transformers and audio speakers since the
electromagnetic elds generated from these devices may distort the video image or
otherwise interfere with camera operaon.
2. Never disassemble the camera beyond the recommendaons in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introducon of
corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creang
unbalanced illuminaon beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, re.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens ssue or a coon pped applicator and ethanol to clean
the sensor and the camera lens. Use a damp so cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7. Do not operate the camera beyond the specied temperature, humidity or power source
rangs. This camera is suitable for indoor operaon only. Use the camera at temperatures
within -40°C~50 (- °F~1 °F) and humidity less than 80%; this device is not rated a°C 40 22 s
submersible. The input power source is 12VDC or 24VAC. Be sure to connect the proper + / -
polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera
to fail, and such damage is not covered by the warranty.
8. Mounng. Use care in selecng a solid mounng surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounng surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounng to drop ceilings) use a safety wire to provide addional
support for the camera.

3
Safety Noce
Federal Communicaon Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons. However, there is no
guarantee that interference will not occur in a parcular installaon. If this equipment does
cause harmful interference to radio or television recepon, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Cauon: Any changes or modicaons not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two
condions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operaon.
Specyfikacje produktu
Marka: | EverFocus |
Kategoria: | Kamera monitorująca |
Model: | ECD900B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z EverFocus ECD900B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca EverFocus
23 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
Instrukcje Kamera monitorująca
- Kamera monitorująca Qian
- Kamera monitorująca Caliber
- Kamera monitorująca Chacon
- Kamera monitorująca Iiquu
- Kamera monitorująca JVC
- Kamera monitorująca Aida
- Kamera monitorująca Marshall Electronics
- Kamera monitorująca Brinno
- Kamera monitorująca Enabot
- Kamera monitorująca Nextech
- Kamera monitorująca Crestron
- Kamera monitorująca Exibel
- Kamera monitorująca Genie
- Kamera monitorująca Canon
- Kamera monitorująca Conbrov
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025