Instrukcja obsługi Futaba DLPH-1

Futaba Zdalne sterowanie DLPH-1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Futaba DLPH-1 (1 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 5.0 gwiazdek

Pobierz PDF

Strona 1/1

ReceiverLink

ReceiverLinkReceiverLink

BatteryF/S

Precautions

PrecautionsPrecautions

1.

Install two receivers on the aircraft as shown in the wiring diagram on the

next page.

2.

Link the two receivers using the dual receiver feature of the transmitter.

For systems without dual receiver capability, link each receiver in turn.

WARNING

Failuretofollowthesesafetyprecautionsmayresultinsevereinjurytoyourselfandothers.

Inordertopreventanyshortcircuits,pleaseobservethepolarityofall

connections.

Ensurethattheunitisconnectedproperlytothereceiver.

■

If the connector is disconnected during ﬂight, it becomes inoperable.

Ensurethattheunitismountedinanareathatwilleliminateexposureto

fuelandwater.

■

As with any electronic components, proper precautions are urged to pro-

long the life and increase the performance of the unit.

Allowaslightamountofslackintheunitcablesandfastenthemata

suitablelocationtopreventanydamagefromvibrationduringﬂight.

Besuretolinkthetworeceiverswiththetransmitter.

■

It will not work unless the two receivers are linked. After startup, even if

the link on one side is disconnected, the other side will continue to oper-

ate normally.

UsedinasetofFutabaS.BUS/S.BUS2systems.

DonotsupplyreceiverpowerfromtheESC.Whenusingthereceiver

powersupplytypeESC,removethered(+)cordofthe3chwiringfrom

theESCsothatthepowerisnotsuppliedfromtheESC.

■

Use a dedicated battery to power the receiver / servo.

Donotconnecttheservoandtelemetrysensordirectlytothereceiver.

■

Large current ﬂows through the Rx port of DLPH-1 and is damaged.

Donotconnectahighvoltagebatterybeyondthespeciﬁcationsofthe

servoused.

■

There is a risk of explosion, ﬁre and damage.

Donotusemorethan60Aforamoment.

■

Reference: Although it depends on the servo used and ﬂight style, acro

ﬂight with 15 HPS servos has been conﬁrmed.

To en su re tha t t he  DLPH- 1 i s f uncti on in g as de si re d, ple as e t es t

accordingly.

■

Do not ﬂy until inspection is complete.

Beforetheflight,disconnectthewiringofthemainreceiverfromthe

DLPH-1thatisoperatingnormally,andcheckifthesubreceiveralone

cancontrolit.

■

Check if the DLPH-1 switches.

DonotusetheDLPH-1withanythingotherthananR/Cmodel.

Transmitterinlinkmode Transmitterinlinkmode

ForFASSTest18CHSelect

dualmodeandlinkprimary

*Followthelinkprocedure

foreachreceivermanual.

ForFASSTest18CHSelectdual

modeandlinksecondary

Turnonthemain

receiverandlink

Turnonthesub

receiverandlink

MainRX

SubRX

Workswiththe

mainreceiver

Troubleoccurredinthe

mainreceiver ！！

DLPH-1automatically

switchestosub-receiver

Switchtothemain

receiverwhen

communicationis

recovered

Appllcablesystems

S.BUS/S.BUS2receiver

*Exceptforcars

Thank you for purchasing the DLPH-1. Before using your new DLPH-1, please

read this manual thoroughly and use the DLPH-1 properly and safely. After read-

ing this manual, store it in a safe place.

Use : Two receivers and two batteries communication

switching device

Size :

62.8×62.4×18.1 mm

( in)2.47×2.46×0.71

Weight : 50 g (1.76 oz)

FET rated :

Always 60 A / 2 pcs

Operating voltage : DC6.4 V to 13.0 V

Accessories:

Switch / Receiver connection cord x 2

/ Mini screwdriver/ Flange damper / Eyelet / Wood screw

◆ Abouttelemetrysystem

Whenusingthedualreceiverfunction

・Thetelemetryfunctionofthemainreceiver

canbeused

・Sub-receivertelemetryfunctionisnotavailable

Otherthandualreceiverfunction

・Telemetrynotavailable

・SettelemetrytoINH(disabled)

TwoS.BUS2/S.BUSReceivers

MainReceiverSubReceiver

7R6%866%86SRUW

:KHQXVLQJ(6&

9DULRXVWHOHPHWU\VHQVRUV6%86J\URHWF

6ZLWFK

(6&

5HFHLYHUق6HUYRك%DWWHU\

ٴ/L)HFHOOV岜9

ٴ/L3RFHOOV岜9

ٴق/L3RFHOOV岜9ك

ٴ/L)HFHOOV岜9

ٴ/L3RFHOOV岜9

ٴق/L3RFHOOV岜9ك

5HFHLYHUق6HUYRك%DWWHU\

6%86

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

&+

6%86

AntennaMakearrangeindiﬀerent

fourdirections.

HowtoUseWiring

FUTABA CORPORATION

Hobby Radio Control Business Center Sales & Marketing Department

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

TEL: +81-475-32-6051, FAX: +81-475-32-2915

©FUTABA CORPORATION 2021, 10 (1)

DonotsupplyreceiverpowerfromtheESC.Whenusingthe

receiverpowersupplytypeESC,removethered(+)cord

ofthe3chwiringfromtheESCsothatthepowerisnotsupplied

fromtheESC.

■

Use a dedicated battery to power the receiver / servo.

This receiver employs an electronic switching (current is controlled by an FET circuit)

system. When the exclusive switch is set to ON or is pulled, the power is turned on.

Switches other than the exclusive switch cannot be used. In addition, since a very

VPDOOFXUUHQWÀRZVHYHQZKHQWKHSRZHULVR൵DOZD\VGLVFRQQHFWWKHEDWWHU\IURPWKH

connector when the receiver is not in use.

One or 2 batteries can be connected. When 2 batteries are connected, the battery with

the highest voltage is used. When only one battery is connected, always insulate the

unused connector. The battery can be connected to either side.

8VHEDWWHULHVZLWKVX൶FLHQWFDSDFLW\IRUWKHVSHFL¿FDWLRQVDQGQXPEHURIVHUYRPRWRUV

to be used.

Evenifthevoltageofone ofthe

batteriesdrops,powerissupplied

fromtheotherbattery.

Evenifthepowersupplywiringof

oneofthebatteriesbreaks,power

issuppliedfromtheotherbattery.

Wh en the sw itc h is se tt o ON ,

pow eris supp lied f rom th e

batterywith thehighestvoltage.

Theoperatingtimeisthetotal

timeofthe2batteries.

E l e c t r i c  p o w e r  w i l l  b e

automaticallyandalternatively

suppliedfromthebatterywhich

voltageishigher.

Battery2 Battery1

Suppliedfrom

battery2

Suppliedfrom

battery1

Suppliedfrom

battery1

BatteryLED

BatteryLEDBatteryLED

Dualbatterysystem

DualbatterysystemDualbatterysystem

7KHEDWWHU\/('RQWKHVLGHEHLQJXVHGOLJKWVXS,WWXUQVR൵ZKHQHDFKEHFRPHV9RUOHVV

Battery2lights

greenwhen6V

orhigher

Battery1lights

greenwhen6V

orhigher

Two power supply batteries can be connected to the DLPH-1. Power is supplied

from the battery with the highest voltage. The operating time is the total time of the 2

batteries. For example, even if the voltage of one battery drops, power can be supplied

IURP WKHRWKHU EDWWHU\ (YHQ RQH EDWWHU\ FDQ EH XVHG EXW VDIHU ÀLJKW LV SRVVLEOH LI 

batteries are used.

DLPH-1

DualRXLinkPowerHUB

1M23N38101

72.0mm

44.8mm

Instruction Manual

Ifoneofthetworeceivers

becomesunreceivable,itwill

automaticallyswitchtothe

otherreceiver.

Automatically

switchesbetweenthe

twobatteries.

Upto18high-performanceservoscanbePWMconnected.

2．

4．

1．

3．

LEDReceiver2（Sub）

Nosignalreception:OFF

Receivingsignals:Green

Receivingerror:Red

LEDReceiver1（Main）

Nosignalreception:OFF

Receivingsignals:Green

Receivingerror:Red

● Li-Fe2cells

orLi-Po3cells

（Li-Po3cells）

Do notconnectthe servo and telemetry

sensordirectlytothereceiver.

Thetwobatteriesshouldnotuse

diﬀerenttypes.

Besuretoremovethebattery

whennotinuse.

Li-po3cell11.4Vcannotbeused

withFutabaHobbyServos.

(asof2021/10)

Telemetryfunction(voltagedisplay)

elemetryfunction(voltagedisplay)

elemetryfunction(voltagedisplay)Telemetryfunction(voltagedisplay)

The DLPH-1 is equipped with a telemetry sensor function. The receiver voltage displayed on the

transmitter home screen is only a constant value. The voltages of battery 1 and battery 2 should

be monitored by telemetry voltage.

DLPH-1 uses two continuous slots. Please note that the proper default start slot for this accessory

is number 6. When setup-changing or adding, it is the following numbers that are made to a start

slot.

1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,18,19,20,21,22,24,25,26,27,28,29,30

By connecting the transmitter and SB2 port, it is possible to register to the transmitter and change

the start slot. In that case, it is necessary to connect the battery to DLPH-1 and supply power.

Information on how to change the slot assignment is included in the transmitter's manual.

Telemetry → Voltage T32MZexample

ReceiverBattery1Voltage

ReceiverBattery2Voltage

Voltageswitch

11.4V

7.6V

6.4V

Mounting hole dimensions

●

)RUUHFHLYHUVWKDWFDQVHWWKHEDWWHU\)6VHWWKHEDWWHU\)6WR9

or less or OFF.

●

Also, make sure that the battery F / S of the two receivers have the same

settings.

6LQFHWKHRXWSXWYROWDJHIURP'/3+LV9LIWKHEDWWHU\)6LVVHWWR

9RUKLJKHUWKHEDWWHU\)6ZLOODOZD\RSHUDWH

InstalltheDLPH-1inawell-

ventilatedplacetocoolit.

*Ifthebatterylevelis40-30%orless,

thereceiverwillnotturnonforsafety.

Besuretoswitchaccordingtothebatteryused.

Iftheswitchpositionandtheconnectedbatteries

aredifferent,powerwillnotbesupplied.

Specyfikacje produktu

Marka:	Futaba
Kategoria:	Zdalne sterowanie
Model:	DLPH-1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Futaba DLPH-1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zdalne sterowanie Futaba

Futaba DLPH-1 Instrukcja

11 Grudnia 2024

Futaba T3PV Instrukcja

11 Grudnia 2024

Futaba SBS-01V Instrukcja

11 Grudnia 2024

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Magnum RC-328 Instrukcja

9 Kwietnia 2025

Medion MD 41169 Instrukcja

6 Kwietnia 2025

Panasonic EUR7722KB0 Instrukcja

6 Kwietnia 2025

Sonos Controller for iPhone Instrukcja

4 Kwietnia 2025

Conrad src 9200 Instrukcja

2 Kwietnia 2025

Hama 20312 - Easytip S9 Instrukcja

1 Kwietnia 2025

Hama 40095 - 5in1 Instrukcja

1 Kwietnia 2025

ELV SRC-7000 Instrukcja

31 Marca 2025

Hama 20320 - Zapman 4in1 Instrukcja

31 Marca 2025

Universal Remote Control UR4U Instrukcja

30 Marca 2025