Instrukcja obsługi Garmin Compact Reactor 40
Garmin
Niesklasyfikowane
Compact Reactor 40
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin Compact Reactor 40 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.8 gwiazdek
Strona 1/6
REACTOR™ 40 HYDRAULIC
Configuration Guide
Important Safety Information
WARNING
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
You are responsible for the safe and prudent operation of your
vessel. The autopilot is a tool that enhances your capability to
operate your boat. It does not relieve you of the responsibility of
safely operating your boat. Avoid navigational hazards and
never leave the helm unattended.
Always be prepared to promptly regain manual control of your
boat.
Learn to operate the autopilot on calm and hazard-free open
water.
Use caution when operating the autopilot near hazards in the
water, such as docks, pilings, and other boats.
CAUTION
When in use, beware of hot motor and solenoid components
and the risk of entrapment from moving parts.
Failure to install and maintain this equipment in accordance with
these instructions could result in damage or injury.
NOTICE
To avoid damage to your boat, the autopilot system should be
installed by a qualified marine installer. Specific knowledge of
hydraulic steering componentry and marine electrical systems is
required for proper installation.
Configuring the Autopilot
The autopilot system must be configured and tuned to your boat
dynamics. The Dockside Wizard and the Sea Trial Wizard are
used to configure the autopilot. These wizards walk you through
the necessary configuration steps.
If your autopilot package did not contain a helm control, you
must configure the autopilot system using a compatible
chartplotter on the same NMEA 2000® network as the autopilot
CCU. Instructions for configuration using either the helm control
or a chartplotter are provided.
Dockside Wizard
NOTICE
If you perform the Dockside Wizard while your boat is out of the
water, provide rudder-movement clearance to avoid damage to
the rudder or other objects.
You can complete the Dockside Wizard while the boat is in or
out of the water.
If the boat is in the water, it must be stationary while you
complete the wizard.
Performing the Dockside Wizard
NOTICE
If you have a boat with a power assist steering system, turn on
the power assist steering system before performing the
Dockside Wizard to avoid damaging the steering system.
1Turn on the autopilot.
The first time you turn on the autopilot, you are prompted to
complete a short setup sequence.
2If the does not start automatically after the Dockside Wizard
setup sequence, select an option:
• On a helm control, select > > Menu Setup Dealer
Autopilot Setup Wizards Dockside Wizard > > .
• On a chartplotter, select > >Settings My Vessel
Autopilot Installation Setup Wizards Dockside > >
Wizard.
3Select the vessel type.
4If prompted, follow the on-screen instructions to set the helm
lock-to-lock,
5If prompted, follow the on-screen instructions to provide the
helm displacement value.
6If necessary, calibrate the rudder sensor (Calibrating the
Rudder Sensor, page 1).
7Test the steering direction (Testing the Steering Direction,
page 1).
8If necessary, select the speed source (Selecting a Speed
Source, page 2).
9If necessary, verify the tachometer (Verifying the
Tachometer, page 2).
10If prompted, test the helm lock-to-lock.
11Review the results of the (Dockside Wizard Reviewing the
Results of the Dockside Wizard, page 2).
Calibrating the Rudder Sensor
NOTE: If an error appears during these steps, the rudder
feedback sensor may have reached its limit. If this happens, the
rudder feedback sensor may not have been installed correctly. If
the problem persists, you can continue with calibration by
moving the rudder to the farthest position that does not report an
error.
1Position the rudder so that the boat would steer fully
starboard, and select .OK
2After the starboard calibration is complete, position the
rudder so that the boat would steer fully port, and select .OK
3After the port calibration is complete, center the rudder
position, let go, and select .Begin
The autopilot takes control of the rudder.
4Without touching the rudder, helm control, or chartplotter,
allow the autopilot to calibrate the rudder.
5Select an option:
• If the calibration did not complete successfully, repeat
steps 1 through 4.
• If the calibration completed successfully, select .OK
Testing the Steering Direction
1While sitting still or moving at a low rate of speed, select
and .
When you select , the rudder must turn the boat to the left.
When you select , the rudder must turn the boat to the right.
2Select .Continue
3Select an option:
• If the steering test turns the boat in the correct direction,
on a helm control, select .Yes
• If the steering test turns the boat in the correct direction,
on a chartplotter, select .Next
• If the steering test turns the boat in the opposite direction,
on a helm control, select , and repeat steps 1 though 3.No
• If the steering test turns the boat in the opposite direction,
on a chartplotter, select , and repeatSwitch Direction
steps 1 though 3.
November 2017
190-02314-00_0A
Specyfikacje produktu
| Marka: | Garmin |
| Kategoria: | Niesklasyfikowane |
| Model: | Compact Reactor 40 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Garmin Compact Reactor 40, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Garmin
10 Stycznia 2025
10 Stycznia 2025
31 Grudnia 2025
14 Października 2024
9 Października 2024
7 Października 2024
4 Października 2024
4 Października 2024
3 Października 2024
2 Października 2024
Instrukcje Niesklasyfikowane
- Natuzzi
- Suunto
- Lazer
- G-Technology
- Quadro
- KeepOut
- Ygnis
- Cilio
- Tsakalis AudioWorks
- Softing
- Pangea Audio
- Ultron
- Saitek
- KitchenAid
- Cresta
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025