Instrukcja obsługi Garmin GT34UHD-TM

Garmin Niesklasyfikowane GT34UHD-TM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin GT34UHD-TM (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 3.5 gwiazdek

Pobierz PDF

Strona 1/4

TRANSOM/TROLLING MOUNT

TRANSDUCER

INSTALLATION

INSTRUCTIONS

Important Safety Information

WARNING

See the guide in the Important Safety and Product Information

chartplotter or fishfinder product box for product warnings and

other important information.

You are responsible for the safe and prudent operation of your

vessel. Sonar is a tool that enhances your awareness of the

water beneath your boat. It does not relieve you of the

responsibility of observing the water around your boat as you

navigate.

CAUTION

Failure to install and maintain this equipment in accordance with

these instructions could result in damage or injury.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, you must install the Garmin® device according to these

instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation, go

to for more information.support.garmin.com

Software Update

You must update the Garmin chartplotter software when you

install this device.

If your chartplotter has Wi Fi‑® technology, you should update the

software using the ActiveCaptain® app on a compatible Android

™

or Apple® device.

If your chartplotter does not have Wi Fi technology, you should ‑

update the software using a memory card and a Windows® or

Mac® computer.

For more information, go to .support.garmin.com

Tools Needed

• Drill and drill bits

• Number 2 Phillips screwdriver

• Masking tape

• Marine sealant

Mounting Consideration

To ensure peak performance with the lowest noise and

interference, you should route the transducer cable away from

ignition wires, house batteries and wires, trolling motor batteries

and wires, and high-energy wires such as radar, audio amplifier,

and autopilot pump wires.

Preparing the Transducer for Long-Term Exposure to

Water

NOTICE

Do not use acetone or acetone-based products on the

transducer. Acetone damages the plastic transducer housing.

When you install a transducer on a boat that spends a

significant amount of time in the water, you should coat the

transducer and mounting hardware with a water-based anti-

fouling paint to prevent marine growth.

1Lightly sand the transducer and mounting hardware with a

fine-grit abrasive pad.

2Wipe the transducer and mounting hardware with isopropyl

alcohol.

3Apply water-based anti-fouling paint to the transducer and

mounting hardware.

Installing the Transducer on a Transom

Mounting Location Considerations

• The transducer should be mounted parallel to the water line.

• The transducer should be mounted as close to the center of

the boat as possible.

• If your propeller moves clockwise when the boat moves, the

transducer should be mounted on the starboard side.

• If your propeller moves counter-clockwise when the boat

moves, the transducer should be mounted on the port side.

• The transducer should not be mounted behind strakes, struts,

fittings, water intake or discharge ports, or anything that

creates air bubbles or causes the water to become turbulent.

The transducer must be in clean (non-turbulent) water for

optimal performance.

• The transducer should not be mounted in a location where it

might be jarred when launching, hauling, or storing.

• On single-drive boats, the transducer must not be mounted in

the path of the propeller.

The transducer can cause cavitation that can degrade the

performance of the boat and damage the propeller.

• On boats with outboard or inboard/outboard motors, the

transducer should be mounted at least 38 cm (15 in.) from

the propeller.

• On twin-drive boats, the transducer should be mounted

between the drives, if possible.

Assembling the Transducer with a Transom Mount

Bracket

1 Attach the mount to the transducer with the included

star washers , and screws .

GUID-D3F0E62E-688B-4A6E-B061-D35EB013F5FB v1February 2020

Specyfikacje produktu

Marka:	Garmin
Kategoria:	Niesklasyfikowane
Model:	GT34UHD-TM
Wysokość produktu:	28.5 mm
Szerokość produktu:	10.3 mm
Głębokość produktu:	10.3 mm
Waga produktu:	7.5 g
Pojemność baterii:	50 mAh
Technologia baterii:	Alkaliczny
Rodzaj baterii:	Jednorazowa bateria
Model:	p 23 ga
Napięcie baterii:	12 V
Liczba baterii włączone:	1 szt.
Stylowe adidasy:	Modne trampki