Instrukcja obsługi Garmin Reactor 40 Steer-by-wire
Garmin
Niesklasyfikowane
Reactor 40 Steer-by-wire
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin Reactor 40 Steer-by-wire (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 5.0 gwiazdek
Strona 1/6
REACTOR™ 40 STEER-BY-
WIRE
Configuration Guide
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
You are responsible for the safe and prudent operation of your
vessel. The autopilot is a tool that enhances your capability to
operate your boat. It does not relieve you of the responsibility of
safely operating your boat. Avoid navigational hazards and
never leave the helm unattended.
Always be prepared to promptly regain manual control of your
boat.
Learn to operate the autopilot on calm and hazard-free open
water.
Use caution when operating the autopilot near hazards in the
water, such as docks, pilings, and other boats.
CAUTION
When in use, beware of hot motor and solenoid components
and the risk of entrapment from moving parts.
Failure to install and maintain this equipment in accordance with
these instructions could result in damage or injury.
NOTICE
To avoid damage to your boat, the autopilot system should be
installed by a qualified marine installer. Specific knowledge of
hydraulic steering componentry and marine electrical systems is
required for proper installation.
Configuring the Autopilot
The autopilot system must be configured and tuned to your boat
dynamics. The Dockside Wizard and the Sea Trial Wizard are
used to configure the autopilot. These wizards walk you through
the necessary configuration steps.
If your autopilot package did not contain a helm control, you
must configure the autopilot system using a compatible
chartplotter on the same NMEA 2000® network as the autopilot
CCU. Instructions for configuration using either the helm control
or a chartplotter are provided.
Dockside Wizard
NOTICE
If you perform the Dockside Wizard while your boat is out of the
water, provide rudder-movement clearance to avoid damage to
the rudder or other objects.
You can complete the Dockside Wizard while the boat is in or
out of the water.
If the boat is in the water, it must be stationary while you
complete the wizard.
Performing the Dockside Wizard
NOTICE
If you have a boat with a power assist steering system, turn on
the power assist steering system before performing the
Dockside Wizard to avoid damaging the steering system.
1Turn on the autopilot.
The first time you turn on the autopilot, you are prompted to
complete a short setup sequence.
2If the does not start automatically after the Dockside Wizard
setup sequence, select an option:
• On a helm control, select Menu > > Setup Dealer
Autopilot Setup Wizards Dockside Wizard > > .
• On a chartplotter, select > >Settings My Vessel
Autopilot Installation Setup Wizards Dockside > >
Wizard.
3Select the vessel type.
4Test the steering direction (Testing the Steering Direction,
page 1).
5If necessary, select the speed source (Selecting a Speed
Source, page 1).
6If necessary, verify the tachometer (Verifying the
Tachometer, page 1).
7Review the results of the (Dockside Wizard Reviewing the
Results of the Dockside Wizard, page 2).
Testing the Steering Direction
1While sitting still or moving at a low rate of speed, select
and .
When you select , the rudder must turn the boat to the left.
When you select , the rudder must turn the boat to the right.
2Select .Continue
3Select an option:
• If the steering test turns the boat in the correct direction,
on a helm control, select .Yes
• If the steering test turns the boat in the correct direction,
on a chartplotter, select Next.
• If the steering test turns the boat in the opposite direction,
on a helm control, select No, and repeat steps 1 though 3.
• If the steering test turns the boat in the opposite direction,
on a chartplotter, select Switch Direction, and repeat
steps 1 though 3.
Selecting a Speed Source
Select an option:
• If your steering-controller connection supplies RPM data,
or you connected one or more NMEA 2000 compatible
engines to the NMEA 2000 network, select Tach. - NMEA
2000 or Proprietary.
• If your steering-controller connection does not supply
RPM data, and if a NMEA 2000 tachometer data source is
not available from one or more engines, or if it is
unusable, select as a speed source.GPS
NOTE: Garmin
® recommends using an external GPS
antenna mounted with a clear view of the sky to provide
reliable and accurate GPS speed information.
• If your steering-controller connection does not provide
RPM data, if you did not connect a NMEA 2000 engine,
and you do not have a GPS device to use as a speed
source, select .None
NOTE: NoneIf the autopilot does not perform well using
as the speed source, Garmin recommends connecting a
tachometer through the NMEA 2000 network or using an
external GPS antenna as the speed source.
Verifying the Tachometer
This procedure does not appear when GPS or None is selected
as the speed source.
With the engine (or engines) running, compare the RPM
readings on the helm control with the tachometer (or
tachometers) on the dashboard of your boat.
If the RPM numbers do not align, there may be a problem
with the NMEA 2000 speed source or connection.
November 2017
190-02318-00_0A
Specyfikacje produktu
| Marka: | Garmin |
| Kategoria: | Niesklasyfikowane |
| Model: | Reactor 40 Steer-by-wire |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Garmin Reactor 40 Steer-by-wire, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Garmin
10 Stycznia 2025
10 Stycznia 2025
31 Grudnia 2025
14 Października 2024
9 Października 2024
7 Października 2024
4 Października 2024
4 Października 2024
3 Października 2024
2 Października 2024
Instrukcje Niesklasyfikowane
- Telycam
- Millecroquettes
- Kunath
- Omnitron Systems
- MOON
- Leatt
- FontaFit
- Cateye
- Kasp
- Beretta
- FED
- Clearblue
- South Shore
- Cactus
- PcDuino
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025