Instrukcja obsługi Hikvision DS-PM-WO2
Hikvision
Niesklasyfikowane
DS-PM-WO2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hikvision DS-PM-WO2 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.6 gwiazdek
Strona 1/6
45
2
RF Frequency 433MHz
RF Modula on FM
Transmisson Speed 10.0kbps
RF Transmisson Distance 800m (Open area)
Output Mode (NO/NC) 30 VDC/1A
Power Supply DC19V to DC15V
Inidcator
3 panel status indicators
8 internal relay status indicators
Tamper-proof
1 rear TAMPER bu om
1 front panel TAMPER buon
Internal Bu on Expander registra on
DIP Switch Enable/Disable indicator
Temperature
-10 to 55℃ ℃
Humidity 10% to 90%
Dimension (L × W × H) 160mm × 105mm ×28mm
Weight 165.0g
Installa on Wall-moun ng
Wireless Output Expander
Wireless Output Expander
Quick Start Guide
Product Informaon
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology
Co., Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings,
pictures, graphs are the properes of Hangzhou Hikvision
Digital Technology Co., Ltd. or its subsidiaries (hereinaer
referred to be “Hikvision”). This user manual (hereinaer
referred to be “the Manual”) cannot be reproduced,
changed, translated, or distributed, parally or wholly, by
any means, without the prior wrien permission of
Hikvision. Unless otherwise spulated, Hikvision does not
make any warranes, guarantees or representaons,
express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Control Panel
The Manual includes instrucons for using and managing
the product. Pictures, charts, images and all other
informaon hereinaer are for descripon and explanaon
only. The informaon contained in the Manual is subject to
change, without noce, due to firmware updates or other
reasons. Please find the latest version in the company
website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of
professionals.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL
FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGE-
MENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE
TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,
OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN
CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET
ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR
OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBI-
LITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR
OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY
RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK
ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING
THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE
LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL
AND THE APPLICABLE LAW, THE LATER PREVAILS.
Trademarks Acknowledgement and other
Hikvision’s trademarks and logos are the properes of
Hikvision in various jurisdicons. Other trademarks and
logos menoned below are the properes of their
respecve owners.
English
Diagram Reference
1
①
②
③
④
⑤
⑥ ⑦
2
3
4
5
① ②
1Expander Wiring
Format the Expander:
Power the expander off. Hold the formang key and power the expander
on at the same me. Signal strength indicator flashes three mes in red
when the formang is completed.
Select NO/NC Mode:
Turn the switch to the CNX terminal to set the mode as NC. Turn the switch
to the terminal to set the terminal as NO.
2Dimension
3Appearance
4Installaon
1. Check Signal Strength
1) Enter the signal checking mode by operang on the control panel. Wait for
the voice announcement to finish.
2) Hold the TAMPER buon for 2 seconds to trigger the tampering alarm,
and then observe the light of signal strength indicator.
Detector indicator turns green: Strong Signal.
Detector indicator turns red: Weak Signal.
2. Wire and route cables.
3. Install the rear panel: Secure the rear panel on the wall with 5 screws.
4. Fix the front panel on the rear panel by ghtening the set screw.
① Front Cover ③ Rear Cover
② ④ Screw Wall
5Register Expander
Register Expander Locally:
Power on the security control panel. Press the registraon key once and
add the expander accroding to the voice prompt.
Note: The distance between the security control panel and the expander
should be less than 50 cm.
Registering Expander via APP:
1.Log in to the APP Store and input “Hik-Connect” to search the mobile
client. Download and install Hik-Connect to your phone.
2.Aer installing, tap to run the client.
3.Power on the security control panel.
4.Log in the Hik-Connect and tap the icon“+” at the upper-right coner of the
Hik-Connect page to add the security control panel. You can scan the QR
code on the device rear panel or on the package box, or input the device
serial No. manually to add the device when the device is in the registraon
mode.
5.Aer adding the security control panel, tap the alarming status icon on
the right of the security control panel's name to enter the Paron page.
6.Tap the “+” icon on the Paron page to add the peripherals.
6DIP Switch
① Enbale the indicators Disable the indicators②
③ Power Indicator: Solid green aer power on
② Fault Indicator: Orange - Fault
① Signal Strength Indicator: Under the signal strength checking mode:
Green - Strong Signal Red - Weak Signal/
④ Register Buon / Formang Buon
⑤⑥ Terminals ⑦ DIP Switch
Specificaon
6
1 1
NO/
NC7
NO/
NC8 COM7COM8
NO/
NC2
NO/
NC1 COM2COM1VCCGND GND
NO/
NC5
NO/
NC6 COM5COM6
NO/
NC4
NO/
NC3 COM4COM3
Alarm Output
(Dry Contact)
Alarm Output
(Dry Contact)
CN7 CN8 C N9
CN6
CN5
CN10
CN12
CN11
Forma ng
S itchw
DIP S itchw
Tamper
S itchw
1 1
1 1
within 50cm
①
②
③④
105
160
28
Specyfikacje produktu
| Marka: | Hikvision |
| Kategoria: | Niesklasyfikowane |
| Model: | DS-PM-WO2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hikvision DS-PM-WO2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Hikvision
11 Stycznia 2025
30 Grudnia 2025
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
8 Grudnia 2024
Instrukcje Niesklasyfikowane
- Laserliner
- ELAC
- Neumann
- Nubert
- Studiologic
- IDENTsmart
- Steelbody
- Medel
- RF Elements
- Schütte
- Moldex
- Infinity
- PVI
- KM-fit
- Eta
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025