Instrukcja obsługi Honeywell HBD95S
Honeywell
Kamera monitorująca
HBD95S
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell HBD95S (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 33 osób i została oceniona przez 17 użytkowników na średnio 4.8 gwiazdek
Strona 1/2
Document 800-09587 – Rev A – 11/11
HBD9 Series Camera Quick Install Guide
800-09587 Rev A 11/11
Camera Overview
Installing the Camera
HBD9 Series cameras (HBD92S/HBD92SX/HBD95S/HBD95SX) can be installed on a
wall or ceiling indoors or outdoors.
Mounting the Camera
1. Find a suitable location for mounting the camera. The mounting surface must be
flat and capable of supporting the combined weight of the camera, sunshield,
bracket, and mounting ring (approximately 3.18 lb. [1.44 kg]).
2. Attach the mounting ring to the mounting surface using the four supplied 1-inch
(25.4 mm) self-drilling screws.
3. Attach the camera and bracket to the mounting ring using the four supplied
3/8-inch (9.52 mm) socket cap screws. Tighten the screws using the supplied hex
key.
Note For an outdoor wall mount installation, ensure that the notch in the base of the bracket is
facing down.
Positioning the Camera
You can position the camera to capture the desired field of view by adjusting the multi-
directional bracket. To change the camera position, loosen the bracket screws with
the supplied hex key, reposition the camera, and then tighten the screws.
Connecting the Camera
1. Connect the camera’s BNC video output to the video input on your monitor or
digital video recorder.
2. Connect the camera’s 12 V DC power output to a power supply appropriate for
your installation (24 V AC or 12 V DC).
Figure 1 Video and Power Connections
Note
When the main video is connected to a terminated monitor or recording device, if the
second video out is also connected to a terminated monitor, the video will become darker.
For correct video level, ensure that only
one
video output is terminated with a 75 ohm load.
Configuring the Camera
Setting the Focus and Zoom
The focus and zoom controls are located on the underside of the camera.
Figure 2 Focus and Zoom Controls*
To set the focus:
1. Loosen the focus set screw using the supplied hex key.
2. Turn the focus adjustment screw clockwise for near focus (N) or
counterclockwise for far focus (
∞).
3. Tighten the focus set screw to lock the focus setting.
To set the zoom:
1. Loosen the zoom set screw using the supplied hex key.
2. Turn the zoom adjustment screw clockwise to decrease zoom (W) or
counterclockwise to increase zoom (T).
3. Tighten the zoom set screw to lock the zoom setting.
Setting the LED Brightness
You can adjust the LED brightness level in night (B/W) mode. The LED brightness
control is located on the underside of the camera, next to the focus and zoom
controls. Unscrew the cap to access the control board.
Figure 3 Camera Control Board
To set the LED brightness:
Turn the LED LEVEL adjustment screw either clockwise to increase the LED
brightness or counterclockwise to decrease the LED brightness.
Programming the Camera
You can program the camera using the onscreen display (OSD) menus. The menu
controls are located on the camera control board (Figure 3). Move the OSD controller
joystick up, down, left, or right to navigate through the menu options. Press the
joystick to execute (set) a selection or to enter a submenu (
).
Figure 4 Setup Menu Structure
Sunshield
Mounting
Ring
Bracket
Notch
Video (BNC) - Yellow
Power (12 V DC) - Red
N
T W
Zoom Adjustment Screw
Focus Adjustment Screw
SETUP
LED LEVEL
VIDEO
TEST
OSD Controller
LED Adjustment Screw
2nd Video Out
<<SETUP MENU>>
LENS DC
EXPOSURE
WHITE BAL ATW
SSDR OFF
BACKLIGHT OFF
DNR3 ON
DAY/NIGHT EXTERN
SPECIAL
EXIT SAVE
1
2
3
4
5
6
7
8
9
LENS DC
EXPOSURE
WHITE BAL
SSDR
BACKLIGHT
SPECIAL
DAY/NIGHT
DNR3
BRIGHTNESS, SHUTTER, AGC,
SENS-UP, RETURN
ATW, OUTDOOR, INDOOR,
MANUAL, AWCSET
OFF, ON
OFF, BLC, HLC
ON, OFF
EXTERN, COLOR, B/W, AUTO
See Special Menu Structure.
Main Setup Menu Menu OptionsSubmenu
* The HBD92S(2.8–12 mm) controls are shown here.
The controls appear in reverse order on the HBD95S (5–50 mm).
Specyfikacje produktu
| Marka: | Honeywell |
| Kategoria: | Kamera monitorująca |
| Model: | HBD95S |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Honeywell HBD95S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca Honeywell
21 Grudnia 2024
21 Grudnia 2024
23 Września 2024
19 Września 2024
14 Września 2024
13 Września 2024
11 Września 2024
10 Września 2024
10 Września 2024
10 Września 2024
Instrukcje Kamera monitorująca
- Broan
- ClearView
- Oplink
- EverFocus
- REVO
- Promise Technology
- Exibel
- Costar
- VisorTech
- Valueline
- Friedland
- EnGenius
- Raymarine
- Atlantis Land
- IPX
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025