Instrukcja obsługi Husqvarna 576XP AutoTune
Husqvarna
Maszyna do piłowania
576XP AutoTune
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Husqvarna 576XP AutoTune (44 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.9 gwiazdek
Strona 1/44
EEEEnnnngggglllliiiisssshhhh
570 AutoTune
576XP AutoTune
576XPG AutoTune
Operator′s manual
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
KEY TO SYMBOLS
2 – English
Symbols on the machine:
WARNING! Chain saws can be
dangerous! Careless or incorrect use
can result in serious or fatal injury to the
operator or others.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
Always wear:
• Approved protective helmet
• Approved hearing protection
• Protective goggles or a visor
This product is in accordance with
applicable EC directives.
Noise emission to the environment
according to the European Community’s
Directive. The machine’s emission is
specified in chapter Technical data and
on label.
Decompression valve: The valve is to
reduce the pressure in the cylinder and
make starting easier. You should always
use the decompression valve when
starting the machine.
Ignition; choke: Set the choke control
in the choke position. This should
automatically set the stop switch to the
start position.
Adjustment of the oil pump
If your machine bears this symbol it is
equipped with heated handles.
Chain brake, activated (right)
Chain brake, not activated (left)
Other symbols/decals on the machine refer to special
certification requirements for certain markets.
Symbols in the operator’s
manual:
Switch off the engine by moving the stop
switch to the STOP position before
carrying out any checks or
maintenance.
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
Protective goggles or a visor must be
worn.
Refuelling.
Filling with oil and adjusting oil flow.
The chain brake must be engaged when
the chain saw is started.
WARNING! Kickback may occur when
the nose or tip of the guide bar touches
an object, and cause a lightning fast
reverse reaction, kicking the guide bar
up and towards the operator. May cause
serious personal injury.
CONTENTS
English – 3
Contents
KEY TO SYMBOLS
Symbols on the machine: ..................................... 2
Symbols in the operator’s manual: ....................... 2
CONTENTS
Contents ............................................................... 3
INTRODUCTION
Dear Customer, .................................................... 4
WHAT IS WHAT?
What is what on the chain saw? ........................... 5
GENERAL SAFETY PRECAUTIONS
Before using a new chain saw .............................. 6
Important .............................................................. 6
Always use common sense .................................. 7
Personal protective equipment ............................. 7
Machine′s safety equipment ................................. 7
Cutting equipment ................................................ 10
ASSEMBLY
Fitting the bar and chain ....................................... 16
FUEL HANDLING
Fuel ...................................................................... 17
Fuelling ................................................................. 18
Fuel safety ............................................................ 18
STARTING AND STOPPING
Starting and stopping ........................................... 19
WORKING TECHNIQUES
Before use: ........................................................... 21
General working instructions ................................ 21
How to avoid kickback .......................................... 27
MAINTENANCE
General ................................................................. 29
Carburettor adjustment ......................................... 29
Checking, maintaining and servicing chain saw
safety equipment .................................................. 29
Muffler .................................................................. 31
Starter .................................................................. 32
Air filter ................................................................. 33
Spark plug ............................................................ 33
Lubricating the bar tip sprocket ............................ 34
Needle bearing lubrication ................................... 34
Adjustment of the oil pump ................................... 34
Cooling system ..................................................... 35
”Air Injection” centrifugal cleaning ........................ 35
Winter use ............................................................ 35
Heated handles .................................................... 36
Maintenance schedule ......................................... 37
TECHNICAL DATA
Technical data ...................................................... 38
Bar and chain combinations ................................. 39
Saw chain filing and file gauges ........................... 39
EC-declaration of conformity ................................ 40
Specyfikacje produktu
| Marka: | Husqvarna |
| Kategoria: | Maszyna do piłowania |
| Model: | 576XP AutoTune |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Husqvarna 576XP AutoTune, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna do piłowania Husqvarna
8 Lutego 2025
12 Stycznia 2025
13 Października 2024
16 Września 2024
12 Września 2024
10 Września 2024
9 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
Instrukcje Maszyna do piłowania
- Maszyna do piłowania Toolcraft
- Maszyna do piłowania Global
- Maszyna do piłowania Flex
- Maszyna do piłowania Turbo-Silent
- Maszyna do piłowania Pro-Cut
- Maszyna do piłowania Lionelo
- Maszyna do piłowania Sun Joe
- Maszyna do piłowania Avantco
- Maszyna do piłowania Ergofix
- Maszyna do piłowania Qualcast
- Maszyna do piłowania MSW
- Maszyna do piłowania Batavia
- Maszyna do piłowania Holzmann
- Maszyna do piłowania MacAllister
- Maszyna do piłowania Einhell
Najnowsze instrukcje dla Maszyna do piłowania
3 Kwietnia 2025
3 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
29 Marca 2025