Instrukcja obsługi IBEAM TE-B4PSK
IBEAM
nieskategoryzowany
TE-B4PSK
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla IBEAM TE-B4PSK (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.8 gwiazdek
Strona 1/2
TE-B4PSK
Product Manual
TE-B4PSK
Product Manual
III. Learning Function
If the vehicle has a spare tire or hitch on the back, the
ordinary parking assist system may detect the tire or
hitch which would result in a continuous false alarm.
The learning function on this device can easily remove
false alarms and it will remember the tire or hitch as part
of the vehicle, correcting the alarm. Learning Function
Activation: Make sure there are no objects within 8 feet
from the rear of the vehicle. When the ACC is switched to
the ON position, shift the vehicle from PARK to REVERSE
and back continuously 5 times within 10 seconds, after
doing this the LED light on the display will flash three
times. The flashing LED will confirm that the learning
function is activated and the system will remember the
tire/hitch/bike holder’s, location automatically. NOTE:
When the hitch or tire has been removed, you will have
to relearn the parking assist system so it knows that
obstruction has been removed.
Installation
III. Learning Function
If the vehicle has a spare tire or hitch on the back, the
ordinary parking assist system may detect the tire or
hitch which would result in a continuous false alarm.
The learning function on this device can easily remove
false alarms and it will remember the tire or hitch as part
of the vehicle, correcting the alarm. Learning Function
Activation: Make sure there are no objects within 8 feet
from the rear of the vehicle. When the ACC is switched to
the ON position, shift the vehicle from PARK to REVERSE
and back continuously 5 times within 10 seconds, after
doing this the LED light on the display will flash three
times. The flashing LED will confirm that the learning
function is activated and the system will remember the
tire/hitch/bike holder’s, location automatically. NOTE:
When the hitch or tire has been removed, you will have
to relearn the parking assist system so it knows that
obstruction has been removed.
Installation
The iBEAM TE-B4PSK parking sensor kit consists
of ultrasonic sensors, and a control box. The system
detects the distance between the vehicle and any
obstructions with the use of the ultrasonic sensors
mounted in the bumper and audible warning will be
heard.
The iBEAM TE-B4PSK parking sensor kit consists
of ultrasonic sensors, and a control box. The system
detects the distance between the vehicle and any
obstructions with the use of the ultrasonic sensors
mounted in the bumper and audible warning will be
heard.
Sensor
D
C
B
A
Controller
Sensor
D
C
B
A
Controller
800.221.0932 • iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
800.221.0932 • iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
I. Specifications
Rated Voltage: 12V (9-16V)
Rated Current: 20mA~200mA
Detecting Distance: Rear (0’ – 5’) Front (0’- 2.5’)
Ultrasonic Frequency: 40Khz
Working Temperature: -22°~176°F
II. Connection
1) Sensors should be 1.5 to 2.5 feet from the ground, and
4” to 7” inches apart from each other (depending on
vehicle application).
2) Install parking sensors by drilling holes out of the
back bumper with the supplied 18.5mm hole saw
bit (make sure when using the angle adapters the
I. Specifications
Rated Voltage: 12V (9-16V)
Rated Current: 20mA~200mA
Detecting Distance: Rear (0’ – 5’) Front (0’- 2.5’)
Ultrasonic Frequency: 40Khz
Working Temperature: -22°~176°F
II. Connection
1) Sensors should be 1.5 to 2.5 feet from the ground, and
4” to 7” inches apart from each other (depending on
vehicle application).
2) Install parking sensors by drilling holes out of the
back bumper with the supplied 18.5mm hole saw
bit (make sure when using the angle adapters the
thicker side is facing down, level with the ground
and the UP arrow on the back of the sensor is facing
up), and install parking sensors.
3) The rear sensors A/B/C/D should be installed from left
to right (looking at the bumper). This is also how they
should be plugged into the control box. (Example A: left,
B: mid-left, C: mid-right, D: right)
4) Connect the RED wire to the +12 volt accessory wire.
5) Connect the BLUE wire to the +12 volt reverse light wire.
6) Connect the BLACK wire to a ground (a metal, non-
painted surface).
7) Plug that wiring harness into the parking sensor control
box (labeled power).
8) Run the audible warning device cable through the vehicle
and mount somewhere in vehicle’s cabin where the
device can be clearly heard with no obstructions (avoid
placing cable where it can get pinched or damaged) and
plug cable into the control box.
9) Mount the control box in rear of vehicle in a safe place
away from rain, heat or humidity.
NOTE: 1) The parking sensors are not designed to
be used in vehicles with metal bumpers.
2) The parking sensors are paintable. There are small
rings included that will fit in the groove on the front
of the sensor. When painting, be sure to use these
rings so paint does get into the grooves otherwise
the sensors will not work properly.
3) The parking sensor kit is used as a parking aid.
Please use your mirrors and look around to avoid
hitting any object.
thicker side is facing down, level with the ground
and the UP arrow on the back of the sensor is facing
up), and install parking sensors.
3) The rear sensors A/B/C/D should be installed from left
to right (looking at the bumper). This is also how they
should be plugged into the control box. (Example A: left,
B: mid-left, C: mid-right, D: right)
4) Connect the RED wire to the +12 volt accessory wire.
5) Connect the BLUE wire to the +12 volt reverse light wire.
6) Connect the BLACK wire to a ground (a metal, non-
painted surface).
7) Plug that wiring harness into the parking sensor control
box (labeled power).
8) Run the audible warning device cable through the vehicle
and mount somewhere in vehicle’s cabin where the
device can be clearly heard with no obstructions (avoid
placing cable where it can get pinched or damaged) and
plug cable into the control box.
9) Mount the control box in rear of vehicle in a safe place
away from rain, heat or humidity.
NOTE: 1) The parking sensors are not designed to
be used in vehicles with metal bumpers.
2) The parking sensors are paintable. There are small
rings included that will fit in the groove on the front
of the sensor. When painting, be sure to use these
rings so paint does get into the grooves otherwise
the sensors will not work properly.
3) The parking sensor kit is used as a parking aid.
Please use your mirrors and look around to avoid
hitting any object.
A B C D
A B C D
Display Power
Red Wire: 12 Volt Accessory (+)
Blue Wire: Reverse Light (+)
Gray Wire: Brake Light (+)
Black Wire: Ground
Adj
A B C D
A B C D
Display Power
Red Wire: 12 Volt Accessory (+)
Blue Wire: Reverse Light (+)
Gray Wire: Brake Light (+)
Black Wire: Ground
Adj
Specyfikacje produktu
| Marka: | IBEAM |
| Kategoria: | nieskategoryzowany |
| Model: | TE-B4PSK |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z IBEAM TE-B4PSK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany IBEAM
14 Sierpnia 2024
24 Lipca 2024
31 Maja 2024
Instrukcje nieskategoryzowany
- nieskategoryzowany GeoVision
- nieskategoryzowany Etekcity
- nieskategoryzowany Kluge
- nieskategoryzowany Gossen Metrawatt
- nieskategoryzowany Stihl
- nieskategoryzowany Sebo
- nieskategoryzowany Christmaxx
- nieskategoryzowany XCell
- nieskategoryzowany Acti
- nieskategoryzowany ADDAC System
- nieskategoryzowany CyberPower
- nieskategoryzowany EZVIZ
- nieskategoryzowany Max Pro
- nieskategoryzowany JK Audio
- nieskategoryzowany Twelve South
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024