Instrukcja obsługi Jablotron TP-83
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Jablotron TP-83 (2 stron) w kategorii termostat. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
TP-83 programmable wireless thermostat 1 / 2 MKL51904
The TP-83 programmable wireless indoor thermostat
The TP-83 is a wireless indoor thermostat with a programmable
weekly heating schedule. It is designed for indoor temperature
regulation which balances economy with comfort. The device is
capable of recognizing warm-up persistence characteristics (within 2
days) and will adjust the settings accordingly so that a high level of
operational comfort is achieved. You need not find out how early the
heating should start in order to get to a comfortable temperature at the
desired time. The required timing is configured automatically.
Temperature adjustment can be performed by simply turning the
setting knob.
When combined with an Oasis wireless security system (Jablotron),
the following are possible:
• Switching the heating ON and OFF remotely (by mobile phone,
remote control or Internet).
• Disabling the heating when windows are open.
• Informing the user about heating faults and frost threats (if the
temperature drops below a pre-configured value a warning SMS is
sent).
• Informing on the occurrence of fire (when the temperature is above
a pre-configured value).
Tab
Button
Installation
The TP-83 should be mounted in a dry indoor location. Choose a
mounting location about 1.5 meters above the floor in an area with
good air circulation. Avoid places with draughts, dead air spots and
radiant heat from the sun or appliances. It should not be installed close
to any metal structure or other objects that may obstruct radio signal
transmissions.
1. Release the upper cover by pressing the plastic tab on the bottom
side of the housing
2. Mount the back part on to the desired location.
3. Insert the battery (the polarity is marked on the holder).
4. Close the thermostat.
Enrollment
Install and connect the receiving unit to the heating system. If the
receiving unit was purchased separately then the thermostat must be
enrolled to it – enter enrollment mode on the receiving unit (see its
manual) and either connect the battery to the thermostat or enter menu
M1 (both operations cause an enrollment signal to be sent).
Symbols on the display
Low battery
Heating ON
Time / temperature
display
Manual mode
Time adjustment
Programming
Service menu
Week days
Comfort temperature
Economy temperature
Scheduled time display
Adjustment and programming
All the required parameters can be configured in the adjustment
menu using the knob. The menu is divided into the following parts:
M1 manual temperature-adjustment
M2 setting the economical or comfortable temperature,
time adjustment
M3 weekly programming schedule
M4 service menu
You can enter the menu and scroll through M1 to M4 by pressing and
holding the knob. The desired submenu is selected by releasing the
knob.
Scrolling inside any particular menu M1 to M4 is done by turning the
knob. The currently displayed parameter can be adjusted by pressing
the knob briefly, turning the knob until the desired value is displayed,
and confirming the setting by re-pressing the knob (this will also cause
a return to the menu so that you can configure other parameters
immediately). The adjustment menu is escaped from by pressing the
knob while OK is displayed or automatically after approx. 30 seconds.
1. M1 – manual mode
If set to manual mode, the thermostat performs
fixed temperature regulation regardless of the
weekly schedule. The desired temperature can
be set within the range of t Lo to t Hi. The M1
menu is escaped from by pressing and holding the knob for 2 seconds.
Note: As mentioned above, entering the M1 menu causes an
enrollment signal to be sent.
2. M2 – temperature & time setting
If the M2 menu is entered, turning the knob will scroll through the
Economical temperature ( ), Comfortable temperature ( ) and Time
() parameters followed by an OK option.
Mo
Each parameter can be entered by briefly pressing the knob. When
or is entered the displayed temperature flashes and can be
adjusted by turning the knob (re-pressing the knob confirms the
setting). The Time parameter adjustment is similar but requires three
steps – for the day, hour and minutes.
3. M3 – programming the weekly heating schedule
This mode allows you to program when the thermostat should switch
between Day ( ) and Night ( ) operation. The heating schedule can
be programmed either for each day separately or just for working days
or just for the weekend or for all days together.
PRG
SuMo Tu We Th Fr Sa
PRG
SuSa
PRG
Mo Tu We Th Fr
PRG
Mo
Enter the M3 menu, scroll to the desired option by turning the knob
and enter the schedule programming by briefly pressing the knob (this
erases the current schedule setting).
Mo
Mo
Mo
Schedule programming is done by marking
periods of time for which the Day heating
operation is requested. The marking bar is
shown at the bottom of the display, each
hour can be either marked or unmarked.
You mark or unmark by turning the knob.
The mark/unmark mode is displayed by /
symbols, the currently programmed hour is
shown on the display (00 to 23). Switching
between mark/unmark modes is done by
pressing the knob (this applies when turning
clockwise, turning the knob anti-clockwise
always switches to unmark mode).
Turning the knob to the rightmost position
(following hour 23) will display an OK option.
Pressing the knob will then finish
programming.
Specyfikacje produktu
| Marka: | Jablotron |
| Kategoria: | termostat |
| Model: | TP-83 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Jablotron TP-83, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje termostat Jablotron
7 Kwietnia 2025
29 Marca 2025
29 Marca 2025
30 Stycznia 2025
Instrukcje termostat
- Viessmann
- Remeha
- Crestron
- Intertechno
- GENERAL Life
- Plugwise
- Carrier
- Netatmo
- Oertli
- Eqiva
- Perel
- AVM
- Ouellet
- King
- Elektrobock
Najnowsze instrukcje dla termostat
9 Kwietnia 2025
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
6 Kwietnia 2025
6 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025