Instrukcja obsługi Kicker 46HDTPH
Kicker
system hi-fi
46HDTPH
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker 46HDTPH (6 stron) w kategorii system hi-fi. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.5 gwiazdek
Strona 1/6
1. Remove the fairing, tank, and seat according to the manufacturer’s service manual.
2. Plug the 4-pin connector into the front kit’s rear
inputs, then route the RH14HDT harness through the
neck and wiring track to the rear of the bike .
3. Route the harness along the clutch side to the rear pods; notice the tags for the
clutch side and the throttle side.
4. Find the rear speaker 4-pin plug and unplug the resistor pack.
46HDTPH
Tour-Pak Harness Kit Installation Guide for
Harley Davidson® Tour-Pak Motorcycles 2014–Present
Package Contents:
(1) Install Guide (1) Wiring Harness RH14HDT (1) Wiring Harness RH14HDTI
(6) Zip Ties (4) Black Heat Shrink
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service
manual for proper procedures and torque specifi cations. KICKER is not responsible for damage resulting from improper
installation techniques. This kit be compatible with some aftermarket head units.may not
NOTE: It is necessary to re-fl ash your HD radio for 4 speaker set up before installation of this kit. If you do not have the
Techno Research Centurion program software you may purchase a Kicker TRHDP Radio Flash Programmer.
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 46HDTPH-B-20200305
5. Plug in the Rear accessory harness and route the harness along
the clutch side of the bike, alongside the factory harness.
6. Remove the factory speakers.
7. Route both side speaker wires (input
and output) through the factory gromet into
the speaker pod.
8. Connect the speaker wires to the factory or replacement speaker and connect the
input wires to the factory speaker wires. Use shrink wrap over the connections to factory
speaker wires to avoid shorts.
9. Reinstall the speakers and zip tie the
new harness to the factory harness, making
sure the new wiring does not interfere with
the seat.
10. Reinstall the tank, seat, and fairing.
NOTE: It will be necessary to check that the crossover and gains are set properly for the rear speakers if
you’re using factory or Kicker PS65 speakers. The crossover should be set to 80HZ with optimized gain lev-
els. For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00am – 5:00pm CST
or email at support@kicker.com. For installation videos please go to our KICKER YouTube channel.
Package Contents:
(1)
Programmer Module
(1)
USB cable
NOTE
1:
MUST
BE
CONNECTED TO THE INTERNET
NOTE
2:
For motorcycles with:
Stock ECM: Follow the provided instructions below.
(1)
Diagnostic cable
(1)
Instructions
Power Commander: Disconnect the Power Commander from the the ECM circuit. Reconnect ECM to the stock
harness plug and then follow the provided instructions below.
Any Aftermarket ECM: Disconnect your your attermarket ECMand install stock ECMto the the bike harness. Follow
provided instructions below.
(For
some ECMs this
will
mean reinitializing the attermarket ECM when
it
is
reinstalled)
INSTALLING THE SOFTWARE FOR A FIRST TIME USER
1.
Download software program from http://technoresearch.com/index.php/support/downloads
2.
Once the download completes,
Run
software installer.
3.
If
using the Kicker TRHDP connect to your computer using the supplied USB cable.
4.
From the the Icon on your desktop, Start Centurion software.
5.
Allow software to update, accept terms and and conditions select language to launch program.
PROGRAMMING LIKE A PRO
1.
Remove side cover from left side of bike and locate the bottom 6-pin diagnostic plug.
2.
Connect your programmer to this plug.
3.
Turn
ignition switch to the Accessory position.
4.
Launch program
5.
To
connect to the the bike, select icon with two arrows facing each other
6.
Once connected to the the the bike, select icon with Wrench on
it
7.
You
will
now see a . drop-down menu From this menu, you can read and reset DTC's, and complete programing for
adding
KICKER
Audio upgrade kits.
2 SPEAKER FRONT KIT
1.
Select Radio speaker programing
2.
Select 2 Speakers- Front Speaker
Kit
3.
Select Program Speaker
a.
Follow on-screen directions, complete and look for Pass on the menu
4. Select from the drop-down menu: Radio Front Rear amp
5.
Select Front and Start
a.
Click enable and flash
b.
Follow the on-screen directions (confirm Pass)
6.
Exit
the rrogram
Specyfikacje produktu
| Marka: | Kicker |
| Kategoria: | system hi-fi |
| Model: | 46HDTPH |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kicker 46HDTPH, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje system hi-fi Kicker
7 Października 2024
23 Września 2024
10 Września 2024
5 Września 2024
5 Września 2024
31 Sierpnia 2024
31 Sierpnia 2024
28 Sierpnia 2024
27 Sierpnia 2024
27 Sierpnia 2024
Instrukcje system hi-fi
- system hi-fi Pronomic
- system hi-fi Crystal Video
- system hi-fi Cobra
- system hi-fi Teac
- system hi-fi Hosa
- system hi-fi Numan
- system hi-fi Speco Technologies
- system hi-fi Antelope Audio
- system hi-fi Vimar
- system hi-fi ION
- system hi-fi Behringer
- system hi-fi DBX
- system hi-fi Memphis Audio
- system hi-fi Kramer
- system hi-fi Scott
Najnowsze instrukcje dla system hi-fi
9 Kwietnia 2025
5 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
29 Marca 2025
28 Marca 2025
28 Marca 2025