Instrukcja obsługi LiftMaster 041-0347-000
LiftMaster
Niesklasyfikowane
041-0347-000
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LiftMaster 041-0347-000 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 3.5 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
11.
Locate the notch
in the camera’s
opener and
pull down.
12.
Follow the myQ®
App instructions
to add the new
camera to your
myQ® account.
10.
Reattach the
newbadge.
Reconnect
power and
battery, if used.
3.
Using a flat head
screwdriver,remove the
badge at the opener’s
bottom.
Badge is held in by four
clips, pull badge off.
Badge
9.
Align screw
holes and place
camera into
garage door
opener.
Fasten the
three screws
with a Phillips
screwdriver.
To prevent damage to the camera,
push the camera lens closed when
replacing, and hold it in place as
you remove securing hardware.
DO NOT touch the camera logic
board during installation.
ALWAYS wear protective gloves
and eye protection when changing
the battery or working around the
battery compartment.
Introduction
Installation
CAMERA SERVICE KIT REPLACEMENT
Model 041-0347-000
Your camera is accessible at the opener’s bottom side. After installing
the new camera, use your myQ® app to connect your new camera to
your myQ® account.
2.
Disconnect
power to the
garage door
opener, and
remove the
backup battery,
if used.
1.
Using the myQ app,
delete the garage
door opener from
the myQ account
before re-adding the
opener and camera
to the myQ account.
To prevent possible
SERIOUS INJURY or DEATH:
• Disconnect ALL electric
and battery power BEFORE
performing ANY service or
maintenance.
WARNING: This
product can
expose you to
chemicals including lead,
which are known to the
State of California to cause
cancer or birth defects or
other reproductive harm.
For more information go to
www.P65Warnings.ca.gov.
Camera LED Status Indicators
WHAT YOU SEE WHAT IT MEANS
Solid White Camera is powering up.
Flashing Blue Ready to be set up in the myQ
® App.
Solid Blue Connected to your mobile device. You are not yet connected to the Internet. If this
persists after setup, check your home router and Internet. Connecting to Wi-Fi
® and
connecting to the myQ
® App.
Flashing Blue and Green Connecting to Wi-Fi and connecting to the myQ
® App.
Solid Green Connected to the myQ
® App.
Flashing Purple Receiving firmware updates.
Solid Red Camera thermal error state when the camera reaches high heat 60 °C temperature
and cools down.
Tools:
• Phillips Screwdriver
• Flat head Screwdriver
• Ladder
• Masking Tape (optional)
Hardware:
• Screw Qty. (3)
• Decorative Badge
• Camera
NOTICE: This device complies with part 15 of the FCC rules and
Innovation, Science and Economic Development Canada licence-exempt
RSSs. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance
is maintained between users/bystanders and device.
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules and Industry Canada
ICES standard. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The device for operation in the band 5150-5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile
satellite systems.
6.
Open camera
and remove the
three-pronged wire
harness that has
the black, green,
and white wires.
Rotate the
connector clip
backward before
removing the wire
harness.
Connector clip
7.
Open new camera
and place the
three-pronged wire
harness that has the
black, green, and
white wires.
Rotate connector
clip back into place
after reconnection.
Close camera.
5.
Remove the
two-pronged wire
harness with the
black and
white wires.
4.
Unscrew the
camera slowly
from the opener
housing by
removing the
three screws
with a Phillips
screwdriver.
TIP: Use masking tape to
hold the camera in place
as you remove screws.
Masking
Tape
8.
Connect the
two-pronged
wire harness
that has the
black and
white wires.
Specyfikacje produktu
| Marka: | LiftMaster |
| Kategoria: | Niesklasyfikowane |
| Model: | 041-0347-000 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z LiftMaster 041-0347-000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane LiftMaster
7 Października 2024
29 Września 2024
25 Września 2024
23 Września 2024
23 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
Instrukcje Niesklasyfikowane
- Kwikset
- DB Technologies
- SwitchBot
- QNAP
- Signature
- Chipolino
- Ergotron
- Mr. Beams
- Stäubli
- Sport-Tronic
- Trevi
- AdHoc
- Tripp Lite
- Marvel
- Icon
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025