Instrukcja obsługi LiftMaster 050ACTWFATSMC

LiftMaster Niesklasyfikowane 050ACTWFATSMC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LiftMaster 050ACTWFATSMC (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.4 gwiazdek

Pobierz PDF

Strona 1/12

To insert or

remove the wires

from the terminal,

push in the tab with

a screwdriver tip.

Red

White

Grey

White

DANGER PELIGRO

132C2280-3D

TO ER ASE AL L

RECEIVER CODE S

1. Press and HOLD

receiv er ora nge

ERASE button

6 seco nds . Indicato r

light will tu rn ON.

2. Releas e bu tton

when lig ht turn s OFF .

CANADA:

PART NO.: NO. DE PIEZA:

DATE:

THE CHAMB ERLAI N

GRO UP, IN C., USA

Ensa mblad o en México

Ass emble d in Mex ico

ELIMINA CIÓN DE

TODOS LOS CÓDIGOS DE L

RECEPT OR

1. MANT ENGA PRESIONADO

el bo tón na ranja "ERASE"

del re ceptor dura nte 6

seg undo s. La luz de l

indicador se encenderá.

2. Suelte e l botón cuand o la

luz se apague.

DANGER PE LIGRO

132C2280-3D

TO ERASE A LL

RECEIVE R C ODE S

1. Press and H OLDreceiver orange

ERASE butto n

6 seconds. In d i cato r

ligh t wi ll tu rn ON .

2. Release butt o n when l ig h t t u rn s OFF .

CANADA:

P : PIEZ A:ARTN O. NO.DE

DATE:

THE CHAM BERLAIN GROU IN C.,U SAP,

Ensamblado en M éxi co

Assembled in M exi co

ELIMINA CIÓ N DE

TODOSLOS CÓDIGOS DEL

RECEPTOR

1. MANTENGAPRESIONADOel botón n aranj a "ERASE"

del recepto r d u ran te 6

segund o s. La lu z d el

indi cado r se en cend erá.

2. Suelte el b o tón cu an d o la

luz se apag u e.

Before you begin

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Model 050ACTWFATS

1.2 To maintain your warranty, place the

provided label over the existing label

on the end panel of the door operator.

Place the STEP SAVER SETUP label on

the end panel directly below the yellow

LEARN button.

1.1 Remove the light lens by pulling the

top sides of the light lens and rotate the

light lens down. Squeeze the light lens

clips to remove lens from end panel.

Your new myQ® serial number is located on the replacement label with your replacement logic board. You will need this new myQ ® serial number to connect your operator to the network. You will also

have a STEP SAVER SETUP label that must be adhered to your end panel directly under the yellow LEARN button for future identification. This second label indicates your board has been updated, and a

new Product Label should be placed over the current Product Label. Your product may look different.

1.3 Disconnect power to the door operator.

Remove the receiver logic board

2.1 Disconnect the wires from the quick-connect terminals ( ). A

Remove the receiver logic board end panel from the door

operator.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers to remove

the harnesses.

To prevent possible SERIOUS INJURY or

DEATH:

• Disconnect ALL electric and battery