Instrukcja obsługi LiftMaster AELD

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LiftMaster AELD (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 42 osób i została oceniona przez 5 użytkowników na średnio 4.6 gwiazdek

High Low

OFF

ON

Plug-In Loop Detector

for the OmniControl™ Board

Part # AELD

Dip Switch 1 -Sensitivity Level: nty cod Thesesitiviisntrollebythesettingof

switcone deech1 ontgthe fr edof the ttor.

Note:Channg t n gihesesitivitysetting automawill tillyesettheecca r dettor.

Chai e frequ tng t t r. Itisalwangng thencysetiwl notilresehedetectoyseces nsary

to t the detector afterchanging the frequency setting by turning the gaterese

operator power off.

Dip Switch 2 -Boost on/off:Wn t tch 2is off, t boo heheswithesensiivitystis

disabled. When the switch 2is on,the tty boost is enabled. Bo enad sensiiviostble

will inc rease the sensitivity to detect high profile vehicles.

Dip Switch 3 & 4 -Frequency: operag equencyofthedett Thetinfrecoris

conllebysetiswichesfroedtrod the tng of t 3and4on the nt ge of the

detector. Sometimeswhen buriedloopsareinclose proximitytoeach other,it

maybe nsaryto t dnt equ f eachburied op ecesselecifferefrenciesorloto

a opierferen (common cad otalk).voidlontcelyllecrssT actheuallootin p orapeg

frequency is a ction size of t o the numb of s e funofthehelop,erturninth

l, the g of the le- e, d e t of t eque ooplenthadincablanthsetinghefrncy

swiestch (SW 3 & 4).Therefe,setting one tor Lowandthe ot ordeecttoher

to High maynot p a separa of operag equency. T most rovidenytiontinfrhe

accura method of tg t operatitesetinheng frequen multipledet to cyofecrstois

useaequcymertedtotheloopto actuallyreadtheoperangfrenetcoecnnti

frequency. The dettors frequen ould be adjusted thatth aeccyshsoereis

minimum of5kilohertz of separation t abeweenll adjacenops.t lo

LED Functions

– NoPower

ON

– Power Applied

– NoPresence

ON

– P Ddresenceetecte

– Loop OK

.5 Hz Flash

– Open Loop

3 HzFlash

–Srd Loophote

Dip Switches

Dip Switch Functions

www.chamberlain.com

•

•

•

•

The “FAIL” LEDindicates whether or not the loopis within tolerances. If the

loopis outoftolerance,the LEDindicates whether the loopcircuitwas

shorted (3HzFlash)or open(.5HzFlash).When the detector is detecting a

loopfailure it will force a call outputandtheCALL LEDwill be on. Ifthe loop

problemcorrects itself,the detector will begin operating normallyagainand

theLEDwill revert back to the state. FailOff

Failed Loop Diagnostics

Markthe looplayoutonthepavement. Remove sharpinside corners that

can damage the loopwire insulation.

Determint thickn pavemo surethattheepthofthee heess of theent tin d

cutoexd ttcknof the pavemente attemptowill nt ceehe hiess beforting

cutthe ops. Sett sawtocuta depth(typica 2"to2.5") thatloslothelly

will insure a mimum 1"fromtinofhe topof the loopr to the pavementwies

surface. The saw width mustbe larger thanthediameter of the loopwire

to avoid damagth sulatwhen plain e saw cu Cute to e wire inion ced tht.

t op, corn ans,andfd t Remeallromtheheloergleeeerslos.ovdebris f

sawot slwithomp cressed air. Check that the ttomof the cut smohboisot

anddidnotbreak thoughthethicknessof the pavement.

Loop Installation

1

2

G

MS L

CENTER SAFETY EXIT

CENTER SAFETYEXIT

6 twists per ft fromLoop

Turne po thwer OFF to thegate operator.

Plugithe loopdetr iereotn ecton th desid sl

(i.e. center,safety, exit)

Plug the rminalplug (prointevideinto ted) rminal

J8 receptacle on the bottomt oflef the Omni board.

Bring twistedwires frthome loop into the proper

terminal on the terminalplug (i.e. center,safy,et

exit).

Turn the power back on.

Caution:

If u morhan1 loopsinge t

dettor, themtoecset

diffe ntrefrequ .encies

(R toDipSh 3& 4)eferwitc

1.

2.

3.

4.

5.

Plug-In Loop Detector Installation

www.chamber

lai n .c om

detector

vehicular loop

Plug-In Loop Detector

for Liftmaster

Enabled Controllers

MEL # AELDOD

now with BT ROLOOSCONT

Specyfikacje produktu