Instrukcja obsługi Match M 5.4DSP
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Match M 5.4DSP (29 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.8 gwiazdek
Strona 1/29
M 5.4DSP
5-Kanal Miniatur-Verstärker mit 9-Kanal DSP
5-Channel miniature amplier with 9-channel DSP
deutsch / english
micro
29
Dear Customer,
Congratulations on your purchase of this innovative
and high-qual ity MATCH product.
Thanks to more than 30 years of experience in
research and development of audio products this
amplier sets new standards in the range of digital
ampliers.
We wish you many hours of enjoyment with your
new MATCH M 5.4DSP.
Yours,
AUDIOTEC FISCHER
General installation instructions for MATCH
components
To prevent damage to the unit and possible injury,
read this manual carefully and follow all installation
instructions. This product has been checked for
proper function prior to shipping and is guaranteed
against manufacturing defects.
Before starting your installation, disconnect the
battery’s negative terminal to prevent damage
to the unit, re and / or risk of injury. For a proper
performance and to ensure full warranty coverage,
we strongly recommend to get this product installed
by an authorized MATCH dealer.
Install your M 5.4DSP in a dry location with suf -
cient air circulation for proper cooling of the
equipment. The amplier should be secured to
a solid mounting surface using proper mounting
hardware. Before mounting, carefully examine the
area around and behind the proposed installa-
tion location to ensure that there are no electrical
cables or components, hydraulic brake lines or any
part of the fuel tank located behind the mounting
surface. Failure to do so may result in unpredictable
damage to these components and possible costly
repairs to the vehicle.
General instructions for connecting the
M 5.4DSP amplier
The M 5.4DSP amplier may only be installed in
motor vehicles which have a 12 Volts negative ter-
minal connected to the chassis ground. Any other
system could cause damage to the amplier and
the electrical system of the vehicle.
Use only the enclosed cable harness or an op-
tionally available MATCH cable harness for con-
nection of the M 5.4DSP.
ATTENTION: In “HighPower” mode it is man-
datory to connect the M 5.4DSP directly to the
car´s battery, even when using a cable harness-
es out of the MATCH accessories program. Oth-
erwise, it may cause damage to the equipment /
wiring of your vehicle!
Prior to installation, plan the wire routing to avoid
any possible damage to the wire harness. All
cabling should be protected against possible crush-
ing or pinching hazards. Also avoid routing cables
close to potential noise sources such as electric
motors, high power accessories and other vehicle
harnesses.
The fuse may only be replaced by an
identically rated fuse (30 A) to avoid damage of
the amplier.
Congratulations!
General instructions
30
1 System Connector
Connector for the MATCH cable harness.
Make sure that you only use a MATCH origi-
nal connection cable to connect the amplier
to the car radio.
2 Auto Remote
This switch allows to activate / deactivate the
automatic turn-on feature of the amplier.
3 Remote In / Out
The remote input can be used to switch on
the M 5.4DSP. The remote output has to be
used to switch on external ampliers that
are connected to the of the Line Output F - I
amplier.
4 Subwoofer Output
Connector for a passive subwoofer or speak-
er. Use only the enclosed subwoofer cable
for connection.
5 USB Input
Connects the M 5.4DSP to your PC.
6 Control pushbutton
Use this button to either switch between the
setups or initiate a reset of the device.
7 Status LED
The Status LED indicates the operating
mode of the amplier and its DSP memory.
8 Line Output F - I
Line outputs for connecting external ampli-
ers. Make sure that the remote output (Re-
mote Out) is used to turn on these devices.
9 Optical Input
Optical input for digital stereo signals (SPDIF
format).
10 SCP (Smart Control Port)
Multifunction interface for e.g. an optional
remote control or other MATCH M 5.4DSP
accessory.
Connectors and control units
1 2 3
9 10765
4
8
Specyfikacje produktu
| Marka: | Match |
| Kategoria: | odbiornik |
| Model: | M 5.4DSP |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Match M 5.4DSP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Match
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
22 Sierpnia 2024
10 Czerwca 2024
10 Czerwca 2024
Instrukcje odbiornik
- odbiornik CYP
- odbiornik Lindy
- odbiornik Cerwin-Vega
- odbiornik Bowers & Wilkins
- odbiornik Rocstor
- odbiornik FiveO
- odbiornik CE Labs
- odbiornik Morel
- odbiornik Power Dynamics
- odbiornik Clarion
- odbiornik NuPrime
- odbiornik VMV
- odbiornik Optoma
- odbiornik DLS
- odbiornik Dynavox
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025