Instrukcja obsługi Match UP 10DSP
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Match UP 10DSP (26 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.7 gwiazdek
Strona 1/26
UP 10DSP
U P G R A D E
10-Kanal Upgrade-Verstärker mit integriertem
11-Kanal 64 Bit DSP für universelle Anwendungen
10-channel upgrade amplier with integrated
11-channel 64 Bit DSP for universal applications
deutsch / english
28
Dear Customer,
Congratulations on your purchase of this innovative
and high-qual ity MATCH product.
Thanks to more than 30 years of experience in
research and development of audio products this
amplier sets new standards in the range of digital
ampliers.
We wish you many hours of enjoyment with your
new MATCH UP 10DSP.
Yours,
AUDIOTEC FISCHER
General installation instructions for MATCH
components
To prevent damage to the unit and possible injury,
read this manual carefully and follow all installation
instructions. This product has been checked for
proper function prior to shipping and is guaranteed
against manufacturing defects.
Before starting your installation, disconnect the
battery’s negative terminal to prevent damage
to the unit, re and / or risk of injury. For a proper
performance and to ensure full warranty coverage,
we strongly recommend to get this product installed
by an authorized MATCH dealer.
Install your UP 10DSP in a dry location with su-
cient air circulation for proper cooling of the equip-
ment.
For safety reasons, the UP 10DSP must be profes-
sionally installed. Therefore, use the two mounting
plates which are included in delivery. These are at-
tached to the bottom of the amplier with two short
screws which are included in delivery, too.
When screwing the amplier to the vehicle chassis,
carefully examine the area around and behind the
proposed installation location to ensure that there
are no electrical cables or components, hydraulic
brake lines or any part of the fuel tank located be-
hind the mounting surface. Failure to do so may re-
sult in unpredictable damage to these components
and possible costly repairs to the vehicle.
General instruction for connecting the
UP 10DSP amplier
The UP 10DSP amplier may only be installed in
motor vehicles which have a 12 Volts negative ter-
minal connected to the chassis ground. Any other
system could cause damage to the amplier and
the electrical system of the vehicle.
The positive cable from the battery for the entire
sound system should be provided with a main fuse
at a distance of max. 30 cm from the battery. The
value of the fuse is calculated from the maximum
total current draw of the car audio system.
Use only the included MATCH cable or an op-
tionally available MATCH cable harness for
connection of the UP 10DSP. The use of other
cables can result in damage of the ampli-
er, the head unit / car radio or the connected
loudspeakers! The fuses of the amplier may
only be replaced by identically rated fuses
(2 x 25 A) to avoid damage of the amplier.
Prior to installation, plan the wire routing to avoid
any possible damage to the wire harness. All
cabling should be protected against possible
crushing or pinching hazards. Also avoid routing
cables close to potential noise sources such as
electric motors, high power accessories and other
vehicle harnesses.
Congratulations!
General instructions
29
Connectors and control units
1 Speaker Output E - J
Speaker outputs of the channels E - J for
connecting speaker systems.
2 Highlevel Input E - H
Highlevel speaker inputs of the channels
E - H.
3 System Connector
Connector for the MATCH cable harness.
Make sure that you only use a MATCH origi-
nal connection cable to connect the amplier
to the car radio.
4 REM IN / OUT
The remote input can be used to switch on
the UP 10DSP. The remote output has to be
used to switch on external ampliers that are
connected to the Line Out of the amplier.
5 +12 V
Connector for the +12 V power cable to the
positive terminal of the battery.
6 GND
Connector for the ground cable (negative
terminal of the battery or metal body of the
vehicle).
1 2 3 4 5 6
7 USB Input
Connects the UP 10DSP to your PC.
8 Control pushbutton
Use this button to either switch between the
setups or initiate a reset of the device.
9 SCP (Smart Control Port)
Multifunction interface for e.g. an optional
remote control or other MATCH UP 10DSP
accessory.
10 Optical Input
Optical input for digital stereo signals (SPDIF
format).
11 Line Out
Mono line output for connecting external am-
pliers. Make sure that the remote output is
used to turn on these devices.
12 Auto Remote
This switch allows to activate / deactivate the
automatic turn-on feature of the amplier
.
13 Status LED
The Status LED indicates the operating
mode of the amplier and its DSP memory.
13
7 8 9 10 1211
Specyfikacje produktu
| Marka: | Match |
| Kategoria: | odbiornik |
| Model: | UP 10DSP |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Match UP 10DSP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik Match
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
22 Sierpnia 2024
10 Czerwca 2024
10 Czerwca 2024
Instrukcje odbiornik
- odbiornik Sinus Live
- odbiornik DLS
- odbiornik Fenton
- odbiornik AudioSource
- odbiornik Atlas Sound
- odbiornik Loxjie
- odbiornik Vimar
- odbiornik Genie
- odbiornik Amplicom
- odbiornik SoundTube
- odbiornik Legamaster
- odbiornik Inovonics
- odbiornik Maxview
- odbiornik Universal Remote Control
- odbiornik AER
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025