Instrukcja obsługi Moxa SPL-24-T
Moxa
Karta sieciowa/adapter
SPL-24-T
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Moxa SPL-24-T (7 stron) w kategorii Karta sieciowa/adapter. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/7
P/N: 1802000240111
*1802000240111*
SPL 24 Series -
Quick Installation Guide
PoE Splitter
Vers 20ion 6.2 , May 21
Technical Support Contact Information
www.moxa.com/support
2 . A 20 1 Moxa Inc ll rights reserved.
- - 2
Overview
The SPL-24 plays the role of PD, and splits the data signal and power
signal that are transmitted from the PSE. The SPL-24 plays a dual role of
providing power to industrial devices, and enabling Ethernet connections.
The SPL- -24 have a wide operating temperature range of 40 to 75°C, and
are designed to withstand a high degree of vibration and shock. The
rugged hardware design makes the SPL-24 perfect for ensuring that your
Ethernet equipment can operate in critical industrial environments, such
as in hazardous locations, and complies with FCC and CE standards.
NOTE
Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch, and we use SPL as an
abbr
eviation for Moxa PoE Splitter:
SPL = Moxa PoE Splitter
Wiring Requirements
WARNING
Do not disconnect modules or wires unless the power supply has
been switched off or the area is known to be non
-
hazardous. The
devices may only be connected to the
supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra
-
Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra
- Low Voltages (SELV) in compliance with IEC
60950-1/EN 60950-1.
WARNING
The power for this product is intended to be supplied by a Listed
Power Unit, with output marked LPS, and rated to deliver 48 VDC
at a maximum of 300 mA.
WARNING
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950
-1 -1 /EN60950
(or similar regulation).
- - 3
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your
Moxa EtherDevice Switch. Calculate the maximum
possible current in each power wire and common wire.
Observe
all electrical codes dictating the maximum current allowable for
each wire size. If the current goes above the maximum ratings,
the wiring could overheat, causing serious damage to your
equipment.
You should also pay attention to the following items:
• Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
in the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
• Keep the input wiring and the output wiring separated.
• It is strongly advised that you label the wiring to all devices in the
system when necessary.
Package Checklist for SPL-24
The Moxa SPL-24 is shipped with the following items. If any of these items
is missing or damaged, please contact your customer service
representative for assistance.
• - Moxa PoE Splitter, SPL 24
• i g Quick nstallation uide (printed)
• Warranty card
Features of SPL 24-
High Performance Network Switching Technology
• IEEE802.3af compliance
• - Power/data split from PoE lines using either spare pairs or data pairs
• Support for up to 12.95 W at 24 VDC
• Support for up to 15.4 watts per PoE port
• Short circuit protection
• Auto disconnection for over voltage or under voltage
• Power consumption detection and classification
Rugged Design
• Operating temperature range from 0 to 60°C, or extended operating
temperature from - - 40 to 75°C for “ T” models
• IP30, plastic case
• D - IN Rail or panel mounting ability
Specyfikacje produktu
| Marka: | Moxa |
| Kategoria: | Karta sieciowa/adapter |
| Model: | SPL-24-T |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Moxa SPL-24-T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Karta sieciowa/adapter Moxa
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
Instrukcje Karta sieciowa/adapter
- Karta sieciowa/adapter OpenVox
- Karta sieciowa/adapter Eminent
- Karta sieciowa/adapter D-Link
- Karta sieciowa/adapter Vivotek
- Karta sieciowa/adapter Vigitron
- Karta sieciowa/adapter Emtec
- Karta sieciowa/adapter Audac
- Karta sieciowa/adapter LevelOne
- Karta sieciowa/adapter Allnet
- Karta sieciowa/adapter Totolink
- Karta sieciowa/adapter QNAP
- Karta sieciowa/adapter GeoVision
- Karta sieciowa/adapter Iiyama
- Karta sieciowa/adapter Eaton
- Karta sieciowa/adapter Icy Box
Najnowsze instrukcje dla Karta sieciowa/adapter
8 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
29 Marca 2025
14 Marca 2025
14 Marca 2025