Instrukcja obsługi MSR DragonFly
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla MSR DragonFly (2 stron) w kategorii Rożen. Ta instrukcja była pomocna dla 43 osób i została oceniona przez 22 użytkowników na średnio 4.1 gwiazdek
Strona 1/2
MO UN TA I N A F E T Y E S EA R C H S R
8. Put Flame Adjuster Handle onto
DragonFly Cleaning Tool.
Insert tool into Flame Adjuster Tube
and rotate clockwise with pressure
(approximately 20 turns).
9. Tap Flame Adjuster Tube on a hard
surface to remove loosened deposits.
10.
Reinsert Flame Adjuster Valve
Assembly and tighten securely.
11.
Flush the Fuel Line.
Connect stove to Pump
and Fuel Bottle.
Pressurize Fuel Bottle with 10-15
strokes.
Fully open Pump Control Valve
and Flame Adjuster Valve to flush
4 spoonfuls of fuel through Fuel Line
into an appropriate container.
(Jet uninstalled.)
WARNING: Keep away from
ignition sources.
Close and reopen Flame Adjuster
Valve to repeat flushing.
Close Flame Adjuster Valve and
Pump Control Valve and remove
Fuel Line.
Safely dispose fuel when flushing
is complete.
12.
Reassemble stove.
If stove performance is still impaired,
repeat Cleaning the Jet and Flame
Adjuster Valve Assembly steps.
O-rings can become dry, cracked or torn
with use. Their lifespan is affected by dirt,
debris, temperature, friction and frequency
of use. For this reason, please inspect your
O-rings before every trip. Replace dry,
cracked, or torn O-rings immediately, and
replace all O-rings annually, regardless
of appearance. Replacement O-rings and
Pump Seals can be found in the Annual
Maintenance Kit, or the more comprehensive
Expedition Service Kit, purchased separately
from an MSR® dealer.
REPLACING FUEL TUBE O-RING
1. Remove Plunger.
Align, twist, and pull.
2. Remove Fuel Tube Bushing and O-ring
with Jet and Cable Tool.
Remove the O-ring with the end of the
Fuel Line or Safety Pin.
3. Inspect O-ring and replace if damaged.
If needed, a spare green Fuel Tube
O-ring is provided.
4. Lubricate Pump Cup.
Use a drop of Pump Cup Oil or any
mineral-based oil.
5. Insert Plunger.
Hold thumb and forefinger firmly
around .Arrow 1
Align Plunger Bushing Tabs with
holes in Pump Body.
Push Plunger/Bushing into the
Pump Body until it snaps in place.
CLEARING THE JET WITH THE SHAKER NEEDLE
1. Close Pump Control Valve and wait
5 minutes for stove to cool.
2. Shake stove up and down.
Shaker Needle inside Jet should rattle.
3. Preheat and run stove.
If performance does not improve,
perform Cleaning the Jet and
Flame Adjuster Valve Assembly steps.
CLEANING THE JET AND
FLAME ADJUSTER VALVE ASSEMBLY
1. Remove Flame Spreader.
2. Unscrew Jet with Jet and Cable Tool.
Use DragonFly Cleaning Tool with Jet
and Cable Tool for added leverage.
3. Remove Shaker Needle.
NOTE: To exchange Jets, place Shaker
Needle in new Jet and reassemble stove.
4. Clear Jet with Jet Cleaning Wire.
5. Open Flame Adjuster Valve 2 turns.
6. Loosen Stop Nut with Jet and Cable Tool.
Unscrew Flame Adjuster Valve
completely.
Remove Flame Adjuster Valve Assembly.
7. Clean grooved end of Flame Adjuster
with thumbnail or Jet Cleaning Wire.
I N S T R U C T I O N
M A N U A L
DRAGONFLY®
Fo r produc t service and info rm ation contac t
C asc a d e D e s ig n s , Inc .
4 00 0 F i r s t Av e n u e So ut h , S e a t t l e , WA 98 1 3 4 U S A
P h on e : 80 0 . 5 3 1. 9 53 1 o r 2 0 6 . 5 0 5 . 9 5 00
w w w. m s r g e a r . c om ART# 33-305-2 | EN
FOR OUTDOOR USE ONLY
PUMP MAINTENANCE STOVE MAINTENANCE
TROUBLESHOOTING
FUEL INFORMATION
The DragonFly® stove burns a variety of fuels by using two interchangeable Jets.
1. The DG Jet is used for White Gas and Unleaded Auto Gas. This Jet is preinstalled in your stove.
2. The DK Jet is for Kerosene, Diesel, and Jet Fuel. This Jet is included in the parts kit with your stove.
To exchange Jets, see “Cleaning the Jet and Flame Adjuster Valve Assembly.”
Use MSR® SuperFuel™ (White Gas) for optimal performance. It is the highest quality fuel available for your stove.
Do not use leaded fuels. Fuels other than MSR SuperFuel white gas lead to rapid stove clogging and require
more frequent Jet and Fuel Line cleanings. Also, the use of Unleaded Auto Gas may shorten stove lifespan. Use
the fuels chart below to help you find your fuel when traveling internationally.
Visit www.msrgear.com for more information on international fuel names and safe stove transportation.
USA/UK/
Canada
Germany/
Switzerland Japan France Netherlands Spain
White Gas,
Naphtha Kocherbenzin,
Reinbenzin White Gas Pétrole à brûler,
Essence C Wasbenzine Bencina
blanca
Unleaded
Auto Gas Autobenzin Gasoline Essence sans
plomb Benzine Gasolina sin
plomo
Kerosene Petroleum Toh-yu Kérosène Petroleum
Lampolie Parafina
Diesel Diesel Diesel Diesel Diesel Diesel
Problem
Leaking Fuel Cause Solution
At Pump and Fuel Bottle Connection Damaged or missing Pump Seal Replace Pump Seal
At Pump and Fuel Line Connection Damaged or missing Fuel Tube
O-ring Replace Fuel Tube O-ring
At Control Valve Stem Damaged or missing
Control Valve O-ring
Replace Control Valve O-ring
In Pump Plunger Chamber Obstructed Check Valve Clean Check Valve Cavity
Poor Performance Cause Solution
Pump not pressurizing Fuel Bottle Loose or poorly seated Pump
Damaged Pump Cup
Tighten or rescrew Pump
on Fuel Bottle
Replace Pump Cup
Plunger hard to pump Dry Pump Cup Lubricate Pump Cup
Erratic yellow flames Improper preheating Repeat Step 4
Diminished flames Low Fuel Bottle pressure Pump the Plunger
Slow boil times Clogged Jet or Fuel Line Clear Jet and clean Fuel Line
Diminished flames at altitude Insufficient airflow Open Windscreen slightly
Jet and
Cable Tool
Remove O-ring
CONTROL
VALVE
O-RI NG
POPP ET
O-RI NG
Unscrew
Stop Nut
TOP
Remove/Replace
Pump Seal
Remove Check
Valve Assembly
Remove Plunger
ALIGN TWIST PULL
ALIGN
POSITION
Insert Plunger
REPLACING CONTROL VALVE O-RING
AND POPPET O-RING
1. Unscrew Stop Nut 2 turns.
2. Unscrew Pump Control Valve 6 turns.
3. Unscrew Stop Nut completely and
remove Control Valve Assembly.
4. Inspect O-ring(s) and replace if damaged.
Remove Pump Control Valve Handle
from stem.
Slide Stop Nut off.
Remove O-ring(s) with Safety Pin.
REPLACING PUMP SEAL
Inspect Pump Seal and replace if
damaged.
CLEANING THE CHECK VALVE
1. Turn Check Valve Assembly to remove.
2. Wipe any debris from Check Valve
and Pump Cavity.
3. Reinsert Check Valve Assembly.
Shake the
Stove
Remove Flame
Spreader
Unscrew
the Jet
Clear Jet
Orifice
Loosen
Stop Nut
Rotate
Cleaning Tool
Remove old
Fuel Line Filter
REPLACING THE FUEL LINE FILTER
1. Remove old Fuel Line Filter with
Safety Pin.
2. Place new white Fuel Line Filter on
a hard surface.
Center end of Fuel Line over filter.
Push end of Fuel Line until filter is
completely inside.
Deposits in the Jet and Fuel Line reduce fuel flow and impair stove performance. Minor
deposits in the Jet can be cleared with the Shaker Needle. Major deposits may require more
extensive cleaning of the Jet and Fuel Line. At a minimum, perform the following maintenance
annually, or every time you perform the Pump Maintenance.
Do not disassemble stove or pump beyond what is described in these instructions. Disassembly or modification of stove
or pump in any manner not consistent with these instructions voids warranty and can result in an unsafe situation where
fire, burns, severe injury or death can occur.
Do not use stove or pump if parts are missing or broken, or with replacement parts not specific to your stove model. Use
of stove with missing or broken parts, or with replacement parts not specific to your stove model, can result in an unsafe
situation where fire, burns, severe injury or death can occur.
WARNING
Retain these instructions for future reference.
READ, UNDERSTAND, AND FOLLOW ALL instructions and warnings in this manual
before using this stove. Failure to follow warnings and instructions can result in death,
serious burns or other injury, and property damage.
CARBON MONOXIDE, FIRE & EXPLOSION HAZARD
There are serious hazards associated with using this stove and fuel. Accidental
fire, explosion, and misuse can cause death, serious burns, and property dam-
age. You are responsible for your own safety and the safety of those in your
group. Please use good judgment.
This stove is for OUTDOOR USE ONLY. Never use this stove in a tent, vestibule,
car, house, or inside any enclosed area. This stove consumes oxygen and pro-
duces carbon monoxide gas, which is poisonous and has no odor. This stove
can easily ignite nearby combustible materials and flammable liquids or vapors.
If you use this stove in an enclosed area you can be killed or seriously burned.
Keep stove and fuel bottle away from other heat sources. Never use cookware
or an Outback Oven™ with a diameter larger than 10 inches (25 centimeters).
Oversized cookware can overheat the fuel bottle. If you expose the fuel bottle to
high heat, it will explode and you can be killed or seriously burned.
Never let children use this stove. Keep children at least 10 feet (3 m) away from
the stove and cooking area, and supervise them at all times.
DANGER
FOR YOUR SAFETY
CARBON MONOXIDE HAZARD
This stove produces carbon mon-
oxide, which has no odor. Using
it in an enclosed space can kill
you. Never use this stove in an
enclosed space such as a camp-
er, tent, car, or home.
Do not store or use gasoline or other liquids
with flammable vapors in the vicinity of this or
any other stove.
DANGER
Specyfikacje produktu
| Marka: | MSR |
| Kategoria: | Rożen |
| Model: | DragonFly |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z MSR DragonFly, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Rożen MSR
14 Września 2024
13 Września 2024
13 Września 2024
12 Września 2024
11 Września 2024
11 Września 2024
11 Września 2024
11 Września 2024
11 Września 2024
11 Września 2024
Instrukcje Rożen
- Ufesa
- Azzurro
- Activa
- Forge Adour
- Rösle
- Campart
- Wolf
- Ozpig
- Pit Boss
- Inno-Hit
- BergHOFF
- Tenneker
- Balay
- Grill Chef
- Weber
Najnowsze instrukcje dla Rożen
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
29 Marca 2025
27 Marca 2025
12 Marca 2025
4 Marca 2025