Instrukcja obsługi Nectre MK1 LE
Nectre
Podgrzewacz
MK1 LE
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nectre MK1 LE (8 stron) w kategorii Podgrzewacz. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.6 gwiazdek
Strona 1/8
Revision B
Nectre 1 MK LE
Installaon Instrucons
Keep these instrucons for future reference
Glen Dimplex Australia proudly supports the acvies of Landcare Australia through its membership of the AHHA
1
CONTENTS
1. INSTALLATION ................................................................... 1
1.1. IMPORTANT INFORMATION .................................... 1
1.2. FITTING REAR HEAT SHIELD ..................................... 2
1.3. INSTALLING THE HEATER ......................................... 2
1.3.1. Posioning the Heater 2 ........................................
1.3.2. Standard Installaon ........................................... 2
1.3.3. Corner Installaon 3 ..............................................
1.3.4. Clearance Dimensions ......................................... 3
1.3.5. Floor Protector .................................................... 3
1.4. REDUCING CLEARANCES TO COMBUSTIBLES .......... 3
1.5. INSTALLING THE FLUE .............................................. 4
1.6. INSTALLING FIRE BRICKS .......................................... 5
1.7. INSTALLING BAFFLE PLATES 5 .....................................
1.8. INSTALLING ASH PLATE 5 ...........................................
1.9. TECHNICAL DRAWINGS 6 ...........................................
1.9.1. MK1 Legs ............................................................. 6
1.9.2. MK1 Ped .............................................................. 6
1. INSTALLATION
1.1. IMPORTANT INFORMATION
The unit must be installed according to all manufacturers’
instrucons included in manual. The manufacturer is not this
liable for installaons that do not meet the requirements
outlined in this manual.
Most building regulatory authories in Australia require any
wood heater installaon to comply with Installaon Standard
AS/NZS 2918. Dierent states and councils may have varying
regulaons. Check local building regulaons before installing
the appliance.
All Nectre wood heaters have been tested to ensure they will
meet the appropriate safety standard requirements if the
instrucons in this manual are followed. As the safety and
emissions performance can be aected by altering the
appliance, no modicaons are allowed without wrien
permission from the manufacturer.
WE RECOMMEND THAT THE INSTALLATION OF YOUR NECTRE
WOOD HEATER BE CARRIED OUT BY A QUALIFIED INSTALLER.
WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE
INSTALLED IN ACCORDANCE WITH AS/NZS 2918 AND THE
APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING
CODE OR CODES.
WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH
THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS
OF AS/NZS 4012 & AS/NZS 4013 WHERE REQUIRED BY THE
REGULATORY AUTHORITY, I.E. THE APPLIANCE SHALL BE
IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING
‘TESTED TO AS/NZS 4012 & AS/NZS 4013’.
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN
APPROVED IN WRITING BY THE TESTING AUTHORITY IS
CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED
FOR COMPLIANCE WITH AS/NZS 4012 & AS/NZS 4013.
CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM
COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY
RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS
CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
CAUTION: CRACKED AND BROKEN COMPONENTS, EG. GLASS
PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION
UNSAFE.
THE INSTALLATION INSTRUCTIONS IN THIS MANUAL
APPLY TO THE NECTRE 1 WOOD HEATER MODELS. MK LE
THEY HAVE BEEN TESTED FOR EMISSIONS AND
EFFICIENCY AND COMPLY ACCORDING TO AS/NZS 4012 &
AS/NZS 4013.
2
1.2. FITTING REAR HEAT SHIELD
Before working out the posion of the heater and the relevant
clearances to combusble surfaces, t the rear outer heat
shield with the curved end at the top and spacers between
the inner heat shield:
1) On the rear of the heater, there are four 32mm long PK
screws xing the outer heat shield, upside-down, to the
inner heat shield. Remove the screws and the outer heat
shield.
2) Rotate the outer heat shield 180 degrees so that the
curved end is on top and angled towards the front of the
heater.
3) A plasc packet with four 20mm long tubular spacers will
be inside the heater. Re-locate the four 32mm long PK
screws through the original holes in the outer heat shield,
slide a spacer over each screw, and re-fasten to the inner
heat shield.
1.3. INSTALLING THE HEATER
1.3.1. Posioning the Heater
Review the necessary clearances specied in this secon
before considering where to posion the heater.
Also check the praccability of installing the ue system in
relaon to any obstrucng roof beams before posioning the
heater.
The clearance distances can only be reduced if the
surrounding walls are made of non-combusble material such
as stone, brick or concrete. If non-combusble material,
distance can be reduced to 100 mm. Alternavely, shielding of
the wall(s) can reduce clearances (refer to next secon for
more detail).
Clearances to combusble surfaces vary depending on the
type of ue shielding used.
1.3.2. Standard Installaon
Dimensions given in the table and image below represent the
minimum clearance (in millimetres) to combusble materials.
A = Side clearance
B = Rear clearance
C = Minimum oor protector depth from door opening
Specyfikacje produktu
| Marka: | Nectre |
| Kategoria: | Podgrzewacz |
| Model: | MK1 LE |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Nectre MK1 LE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Podgrzewacz Nectre
9 Marca 2025
16 Września 2024
16 Września 2024
15 Września 2024
15 Września 2024
15 Września 2024
15 Września 2024
14 Września 2024
6 Września 2024
5 Lipca 2024
Instrukcje Podgrzewacz
- Podgrzewacz Emos
- Podgrzewacz Maxwell
- Podgrzewacz Jaga
- Podgrzewacz Lavorwash
- Podgrzewacz Solis
- Podgrzewacz Elro
- Podgrzewacz Blaupunkt
- Podgrzewacz Emga
- Podgrzewacz Infratech
- Podgrzewacz Mora
- Podgrzewacz Sinbo
- Podgrzewacz JANDY
- Podgrzewacz Rose LM
- Podgrzewacz Barbecook
- Podgrzewacz Lervia
Najnowsze instrukcje dla Podgrzewacz
4 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
30 Marca 2025
30 Marca 2025
29 Marca 2025
29 Marca 2025
27 Marca 2025
27 Marca 2025