Instrukcja obsługi Nectre N60
Nectre
Podgrzewacz
N60
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nectre N60 (6 stron) w kategorii Podgrzewacz. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.8 gwiazdek
Strona 1/6
Revision A
Nectre N60
Installaon Instrucons
Keep these instrucons for future reference
Glen Dimplex Australia proudly supports the acvies of Landcare Australia through its membership of the AHHA
2
Most building regulatory Authories in Australia require any
wood heater installaon to comply with Installaon Standard
AS/NZS 2918:2018. Dierent states and councils may have
varying regulaons. Check local building regulaons before
installing the appliance.
All Nectre wood heaters have been tested to ensure that they
will meet the appropriate safety Standard requirements if the
instrucons in this manual are followed. As the safety and
emissions performance can be aected by altering the
appliance, no modicaons are allowed without wrien
permission from the manufacturer.
WE RECOMMEND THAT THE INSTALLATION OF YOUR
NECTRE WOOD HEATER BE CARRIED OUT BY A QUALIFIED
INSTALLER.
WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE
INSTALLED IN ACCORDANCE WITH AS/NZS 2918:20 AND 18
THE APPROPRIATE REQUIREMENTS OF THE RELEVANT
BUILDING CODE OR CODES.
WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH
THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS
OF AS/NZS 4012 & AS/NZS 4013 WHERE REQUIRED BY THE
REGUALTORY AUTHORITY, I.E. THE APPLIANCE SHALL BE
IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING
‘TESTED TO AS/NZS 4012 & AS/NZS 4013’.
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT
BEEN APPROVED IN WRITING BY THE TESTING AUTHORITY
IS CONSIDERED TO BE IN BREACH OF THE APPROVAL
GRANTED FOR COMPLIANCE WITH AS/NZS 4012 & AS/NZS
4013.
CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM
COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY
RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION
IS CONSIDERED, THE MANUFACTURER SHOULD BE
CONSULTED IN THE FIRST INSTANCE.
CAUTION: CRACKED AND BROKEN COMPONENTS, EG. GLASS
PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION
UNSAFE.
Your Nectre N60 will arrive mainly fully assembled. The
8mm thick top plate and the pedestal glass insert will be
packed in a cardboard box at the rear of the heater.
Inside the rebox are the following components:
Firebricks 4 bricks @ 270(h) x 175(w) x 25(d)mm –&
2 bricks @ 270(h) x 85(w) x 25(d)mm
Firebrick retainer
Two 6mm thick steel bae plates
Ash pan
Air slide handle
Door handle extension
Assorted bolts and spacers:
o 2 screws @ M6 x 6mm
o 2 washers @ M6
o 4 rebox top spacers 20.5mm x 19mm diameter –
tube
o 4mm & 8mm Allen keys
IMORTANT NOTE: The compliance plate on the rear of
the heater is wrapped in plasc so as not to scratch
the heater when in transit. Remove this plasc cover
to avoid melng it when re is lit.
3.1 Assembling the Main Body
a.
Lay the rebox body down on its “back”. Use a
towel, rug, or the cardboard box it came in to avoid
scratching the heater or the oor.
b.
Unscrew the four screws xing rebox body to the
pallet using a 5/16 hex socket and ratchet.
c.
Remove the square base cabinet from the box and
posion it so that the side with the four holes is
adjacent to the base of the rebox body and the
curved edge is at the top.
3. ASSEMBLING THE HEATER
1. IMPORTANT INFORMATION
2. COMPONENTS
THE INSTALLATION INSTRUCTIONS IN THIS
MANUAL APPLY TO THE NECTRE N60.
IT HAS BEEN TESTED FOR EMISSIONS AND EFFICIENCY
AND COMPLIES ACCORDING TO AS/NZS 4012:2014 &
AS/NZS 4013:2014.
3
d.
Pass the M12 x 60mm screws from the inside
through the four holes in the base cabinet.
e.
Slide a rebox boom spacer (46mm x 19mm
diameter) over each of the M12 screws.
f.
Thread the four M12 screws into the threaded
holes in the base of the rebox.
g.
Before completely ghtening the screws with the
8mm allen key, push the tube spacers out to the
sides of the heater as far as possible and then
ghten the screw. (The reason for this is so that
the ash pan can slide more freely between the
spacers.)
h.
With the base cabinet securely fastened to the
rebox body, tilt the heater upright, and posion it
where it will be installed with the ue (Secon 4.
Installing the Heater).
i.
Place a rebox top spacer (20.5mm x 19mm
diameter) over each of the vercal 12mm diameter
rods on top of the rebox body.
3.2 Posioning the Top Plate
Remove the 8mm thick top plate from the box and place on
top of the heater locang the hole in the plate over the flue
spigot. Adjust the posion of the plate that there an top so is
even space between the top plate and the ue spigot.
3.3 Posioning the Ash pan
The ash pan can now be slid in to the gap created by the
46mm spacers between the rebox body and the base
cabinet. This should slide all the way back, enough so that the
door can then be closed.
4.1 Posioning the Heater
First review the necessary clearances specied before
considering where to posion the heater.
Also check the praccability of installing the ue system in
relaon to any obstrucng roof beams before posioning
the heater.
These clearance distances can only be reduced if the
surrounding walls are made of non-combusble material,
eg. Stone, brick, or concrete. If non-combusble material,
distance can be reduced to 100 mm. Alternavely, shielding
of the wall(s) can reduce clearances (refer to next secon
for more detail).
Depending the type on of ue shielding used, the clearances
to combusble surfaces varies.
4.1.1 Standard Installaon:
AS/NZS 2918:20 18 Standard 6” ue kit
Fied with 900mm stainless steel ue shield
N60 Model
A (mm)
B (mm)
C (mm)
Naked
75
450
250
Curved Sides
100
190
250
Tiled Sides
100
285
250
AS/NZS 2918:20 kit18 Standard 6” ue
Fied with Decromesh & 900mm stainless steel inner shield
4. INSTALLING THE HEATER
N60 Model
A (mm)
B (mm)
C (mm)
Naked
125
450
250
Curved Sides
150
150
250
Tiled Sides
125
240
250
Specyfikacje produktu
| Marka: | Nectre |
| Kategoria: | Podgrzewacz |
| Model: | N60 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Nectre N60, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Podgrzewacz Nectre
9 Marca 2025
16 Września 2024
16 Września 2024
15 Września 2024
15 Września 2024
15 Września 2024
15 Września 2024
14 Września 2024
6 Września 2024
5 Lipca 2024
Instrukcje Podgrzewacz
- Podgrzewacz Kemlan
- Podgrzewacz Eureka
- Podgrzewacz Mora
- Podgrzewacz Uniprodo
- Podgrzewacz Sunheat
- Podgrzewacz Zibro
- Podgrzewacz Zephir
- Podgrzewacz Wanders
- Podgrzewacz Vornado
- Podgrzewacz Haas+Sohn
- Podgrzewacz SuperFish
- Podgrzewacz Solamagic
- Podgrzewacz Clatronic
- Podgrzewacz Calor
- Podgrzewacz Termozeta
Najnowsze instrukcje dla Podgrzewacz
4 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
30 Marca 2025
30 Marca 2025
29 Marca 2025
29 Marca 2025
27 Marca 2025
27 Marca 2025