Instrukcja obsługi Nedis ZBSM10WT

Nedis system alarmowy ZBSM10WT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nedis ZBSM10WT (20 stron) w kategorii system alarmowy. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 3 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/20

a Quick start guide

Zigbee motion sensor ZBSM10WT

For more information see the extended manual

online: ned.is/zbsm10wt

Intended use

The Nedis ZBSM10WT is a wireless, battery powered

motion sensor.

You can connect the product wirelessly to the Nedis

SmartLife app via the Zigbee gateway.

When connected, the current and past motion detection

is displayed in the app and can be programmed to trigger

any automation.

The product is intended for indoor use only.

The product is not intended for professional use.

Any modication of the product may have consequences

for safety, warranty and proper functioning.

Specications

Product Zigbee motion sensor

Article number ZBSM10WT

Dimensions (l x w x h) 46 x 46 x 30 mm

Battery lifetime 1 year

Zigbee frequency range 2405 - 2480 GHz

Maximum transmit power 10 dBm

Antenna gain 2.8 dBi

Temperature range 0 °C - 40 °C

Operating humidity < 100 % RH

Detection range Up to 7 m

Main parts (image A)

1 Function button

2 Status indicator LED

3 Battery insulation tab

Safety instructions

WARNING

• Ensure you have fully read and understood the

instructions in this document before you install or use

the product. Keep this document for future reference.

• Only use the product as described in this document.

• Do not use the product if a part is damaged or

defective. Replace a damaged or defective product

immediately.

• Do not drop the product and avoid bumping.

• This product may only be serviced by a qualied

technician for maintenance to reduce the risk of electric

shock.

• Do not expose the product to water or moisture.

• Children should be supervised to ensure that they do

not play with the product.

• Always keep button cell batteries, both full and empty,

out of reach of children to avoid the chance of

swallowing. Dispose of used batteries immediately and

safely. Button cell batteries can cause serious internal

chemical burns in as little as two hours when

swallowed. Keep in mind that the rst symptoms may

look like child diseases like coughing or drooling. Seek

immediate medical attention when you suspect that

batteries have been swallowed.

• Only power the product with the voltage

corresponding to the markings on the product.

• Do not recharge non-rechargeable batteries.

• Do not dismantle, open or shred secondary cells or

batteries.

• Do not expose cells or batteries to heat or re. Avoid

storage in direct sunlight.

• Do not short-circuit a cell or a battery.

• Do not store cells or batteries haphazardly in a box or

drawer where they may short-circuit each other or be

short-circuited by other metal objects.

• Do not subject cells or batteries to mechanical shock.

• In the event of a cell leaking, do not allow the liquid to

come in contact with the skin or eyes. If contact has

been made, wash the aected area with copious

amounts of water and seek medical advice.

• Observe the plus (+) and minus (–) marks on the cell,

battery and equipment and ensure correct use.

• Do not use any cell or battery which is not designed for

use with the equipment.

• Seek medical advice immediately if a cell or a battery

has been swallowed.

• Always purchase the battery recommended by the

product manufacturer for the product.

• Keep cells and batteries clean and dry.

• Wipe the cell or battery terminals with a clean dry cloth

if they become dirty.

• Use only the cell or battery in the application for which

it was intended.

• When possible, remove the battery from the product

when not in use.

• Properly dispose of the empty battery.

• Battery usage by children should be supervised.

• Some wireless products may interfere with implantable

medical devices and other medical equipment, such as

pacemakers, cochlear implants and hearing aids.

Consult the manufacturer of your medical equipment

for more information.

• Do not use the product at locations where the use of

wireless devices is prohibited due to potential

interference with other electronic devices, which may

cause safety hazards.

Connecting to the Zigbee gateway

4Make sure the Zigbee gateway is connected to the

Nedis SmartLife app.

4For information on how to connect the gateway to the

app, consult the manual of the gateway.

1. Open the Nedis SmartLife app on your phone.

2. Select the Zigbee gateway to enter the gateway

interface.

3. Tap Add subdevice.

4. Remove the battery insulation tab A

The status indicator LED A

2 starts blinking to indicate

pairing mode is active.

4If not, press and hold the function button A1 for 5

seconds to manually enter the pairing mode.

5. Tap to conrm A2 is blinking.

The sensor appears in the app when the product is

successfully connected to the gateway.

Installing the sensor

1. Remove the lm of the tape.

2. Stick the product onto a clean and at surface.

The product is now ready for use.

The overview screen of the sensor

1. Open the Nedis SmartLife app on your phone.

2. Select the sensor you want to view.

The app shows the measured values of the sensor.

• Tap Set alarm to switch the low battery alarm on or o

for the selected sensor.

Creating an automated action

1. Open the Nedis SmartLife app on your phone.

2. Tap Smart scenes at the bottom of the home screen.

3. Tap Automation to open the automation interface.

4. Tap + in the top right corner.

Here you can ll in dierent options to create an

automation.

5. Tap Save.

The new automation appears in the automation interface.

Removing the product from the app

1. Open the sensor interface.

2. Tap the pencil icon in the top right corner.

3. Tap Remove Device.

Declaration of Conformity

We, Nedis B.V. declare as manufacturer that the product

ZBSM10WT from our brand Nedis®, produced in China,

has been tested according to all relevant CE standards

and regulations and that all tests have been passed

successfully. This includes, but is not limited to the RED

2014/53/EU regulation.

The complete Declaration of Conformity (and the safety

datasheet if applicable) can be found and downloaded via:

nedis.com/zbsm10wt#support

Specyfikacje produktu

Marka:	Nedis
Kategoria:	system alarmowy
Model:	ZBSM10WT
Kolor produktu:	Biały
Materiał obudowy:	Plastik
Wysokość produktu:	46 mm
Szerokość produktu:	30 mm
Głębokość produktu:	46 mm
Technologia łączności:	Bezprzewodowy
Zakres temperatur (eksploatacja):	0 - 40 °C
Liczba baterii:	1
Czas eksploatacji baterii:	1 lat(a)
Częstotliwość (MHz):	2405 - 2480 MHz
Typ przetwornika obrazu:	Pasywny czujnik podczerwieni (PIR)
Wykrywacz odległości:	5 m
Moc nadawania:	10 dBmW
ZigBee:	Tak