Instrukcja obsługi Netgear ANT224


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Netgear ANT224 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.7 gwiazdek

Strona 1/2
)NSTALLATION'UIDE
NETGEAR ProSafe Indoor/Outdoor 10 dB 2x2 Directional Antenna ANT224D10
Package Contents
NETGEAR ProSafe Indoor/Outdoor 10 dB 2x2
Directional Antenna ANT224D10
2 lightning arrestors with 30 cm low-loss cables
2 reverse N/SMA adapters
Wall mount and pole mounting hardware
Installation Guide (this guide) and Warranty/
Support card
Ground cable is not included but is required for outdoor
installation. The grounding cable must be equivalent or
better than: AWG 10, UL 1015, Stranded, 600 V, 105 C,
green or green/yellow insulation, 2 clip of 5.5 mm inner
diameter cramped at both ends, cable no longer than 5
meters. Antenna cables are not provided, but are
required to connect to an access point (AP).
Note: For optimal results in extending wireless range, consult a qualified professional
installer service.
Antenna Placement and Location
Antenna placement dramatically affects potential coverage. Follow these guidelines to
maximize coverage:
Place the antenna in a vertical position, connector toward the bottom.
Minimize the obstructions in the front of the antenna. There should be a good visual line
of sight and maximum open space between the antenna and the other antenna(s).
Outdoor point-to-point applications are bridging, repeater mode, or building-to-
building. Mount the antenna on the top of a building on a pole or on an external wall.
For building-to-building transmission you can also install antennas indoors within 10 ft.
of clean windows (no metal coating) in both buildings facing each other. Account for
30-70 % less range than outdoors.
Indoor point to multipoint Warning: The antenna is not omnidirectional and is not
suitable for low ceilings, partial obstructions, walls, cubicles, or when large metal
objects are present.
For best performance with indoor installation, use a short cable between the antenna
and the wireless device. Install the antenna so that it is a minimum of 50 cm (20 in.)
away from people.
First, Mount the Antenna
Then, Connect the Antenna
1. Turn off your wireless access point.
2. This step is only for outdoor installation. For indoor installation, go to step 3.
a. Connect a 30 cm cable (included) to the antenna and to an RF port on the lightning
arrestor.
b. Connect the grounding cable (not included) from the lightning arrestor to the
ground of the building.
Warning: The lightning arrestor and appropriate ground cable must be used for
outdoor installation. NETGEAR does not assume any responsibility in case of
hazard resulting of non-compliance.
c. Screw the N/SMA reverse adapter onto the lightning arrestor RF port.
3. Connect a NETGEAR cable ACC-10314-01, 03,or 04 (sold separately) to the adapter.
4. Locate the primary detachable antennas on the wireless AP. Remove the antennas and
connect the other end of the NETGEAR cable to this port.
5. Reconnect your wireless device to the network and turn it on.
Wall Mounting Pole Mounting
Antenna faces coverage
area. Indoors, put it 2M+
from the floor and above
cubicles. Do not install in
IT rooms or rooms with
metal partitions.
Indoor Connection
Outdoor Connection
Access Point
NETGEAR antenna
cable (sold separately)
N/SMA Adapter
Antenna
Access Point
Lightning
Arrestor
Grounding cable
Ethernet
N/SMA
Adapter
30 cm NETGEAR low-
loss antenna cable(not provided)
Antenna
NETGEAR antenna cable
(sold separately)
ANT224D10 IG.fm Page 1 Monday, July 20, 2009 9:43 AM


Specyfikacje produktu

Marka: Netgear
Kategoria: Niesklasyfikowane
Model: ANT224

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Netgear ANT224, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Netgear

Netgear

Netgear GS504T Instrukcja

25 Stycznia 2025
Netgear

Netgear FV318 Instrukcja

14 Października 2024
Netgear

Netgear GS108Ev4 Instrukcja

9 Października 2024
Netgear

Netgear Orbi RBE972SB Instrukcja

9 Października 2024
Netgear

Netgear Orbi RBK652S Instrukcja

9 Października 2024
Netgear

Netgear Nighthawk MS90 Instrukcja

9 Października 2024
Netgear

Netgear Nighthawk MK93S Instrukcja

9 Października 2024
Netgear

Netgear MS308 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025