Instrukcja obsługi Netgear GS116

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Netgear GS116 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.9 gwiazdek

)NSTALLATION'UIDE

NETGEAR 16-port Gigabit Switch Model GS116

Estimated Time: 5–10 minutes

Unpack the Box and Verify the Contents

When you open the box, verify that you received everything. The package includes:

•NETGEAR 16-port Gigabit Switch Model GS116

•AC power adapter

•Wall-mounting screws

•GS116 Installation Guide (this document)

•Warranty/support information card

If you do not have everything listed above, see the support information card for contact

information. If you are missing the support information card, get contact information at

http://www.NETGEAR.comin the Technical Support section.

Prepare to Install the Switch

Decide where you want to place the switch. Find a flat horizontal surface such as a table,

desk or shelf. The switch comes with wall-mounting screws. You can use the screws if you

want to hang the switch in an open space on a wall.

Make sure the selected location is:

•Not in direct sunlight or near a heater or heating vent.

•Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on

all sides of the switch.

•Well ventilated (especially if it is in a closet).

Also, you will need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each

device you want to connect to the switch. Each Ethernet cable must be less than 328 feet

(100 meters).

Install the Switch and Connect the Other Devices

1.Place the switch on a flat surface or hook onto the screws.

2.For each device, insert one end of an Ethernet cable into the port in the device and

insert the other end into one of the Ethernet ports on the switch.

3.Connect the power adapter cord into the back of the switch and then plug the adapter

into a power source (such as a wall socket or power strip).

The Power light should light up.

4.Check the LEDs to confirm that all connections are correct.

LED Activity

Power• On: 16-port Gigabit Switch has power.

•Off: No power.

RJ-45 ports•Right LED on: 10 Mbps connection to a powered device.

•Left LED on: 100 Mbps connection to a powered device.

•Both LEDs on: 1000 Mbps connection to a powered device.

•Blink: Activity on this port.

072



!UTO

5PLINK

-BPS'IGABIT3WITCH

'3

                  

/N,INK

"LINK!CT

"OTH-

--

6$#!

       

,/#!,

-

).4%2.%4

/&& /.

072



!UTO

5PLINK

-BPS'IGABIT3WITCH'3

                  

/N,INK

"LINK!CT

"OTH-

--

Power

Troubleshooting

Technical Support

Thank you for selecting NETGEAR products.

After completing the Smart Wizare the serial number on the d configuration assistant, locat

bottom label of your product, and use it to register your product at

http://www.NETGEAR.com/register.

Registration on the website or over the phone is required before you can use our telephone

support service. The phone numbers for worldwide regional customer support centers are

on the Warranty and Support Information card that came with your product.

Go to http://kbserver.netgear.com for product updates and Web support.

Problem Action

Power light is not litThe switch has no power. Make sure that:

•The power cord is properly connected to the switch.

•The power adapter is properly connected to a functioning power

outlet. If it is in a power strip, make sure the power strip is turned

on. If the socket is controlled by a light switch, make sure the

switch is in the on position.

•You are using the NETGEAR power adapter supplied with your

switch.

Port number light is

not lit for a connected

device, or stays on

continuously

There is a hardware connection problem.

•Make sure the cable connectors are securely plugged in at the

switch and the device.

•Make sure the connected device is turned on.

•If the Ethernet cable is connected to a NIC or other Ethernet

adapter, make sure the card or adapter is installed correctly and

is working.

•Make sure the cable is less than 328 feet (100 meters).

Specyfikacje produktu