Instrukcja obsługi Panduit TDP43HE
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Panduit TDP43HE (3 stron) w kategorii drukarka. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 3.9 gwiazdek
Strona 1/3
B20747, Rev. 01 Page: 1 of 3 04JUN2015
TDP43HE/TDP46HE
PRINTER RIBBON
SETTING RECOMMENDATIONS
B20747
Rev. 01
04JUN2015
© Panduit Corp. 2015
SETTING THE TDP4*HE PRINTER SPEED OR DARKNESS:
1) When preparing to print, click on “Properties”, to view the printer settings.
2) NOTE: Click on the ABOUT tab to retrieve current driver version.
3) In the OPTIONS tab, set SPEED and DARKNESS, according to the following Table.
Media Type Suggested
Ribbon Type
Suggested Ribbon
Part Number
Printer
Speed
Printer
Darkness
Arc Flash Labels & Tape Resin RHER4BL 3 10
Component Labels, Non-adhesive Polyester Resin RHER4BL 4 10
Component Labels, Paper Hybrid RHEH4BL 3 10
Component Labels, Polyimide, Gloss White Resin RHER4BL 3 10
Component Labels, Polyimide, Matte Tan Hybrid RHEH4BL 4 12
Component Labels, Raised Panel Resin RHER4BL 4 12
Resin RHER4WH 4 12
Component Labels, Standard Polyester Resin RHER4BL 4 10
Component labels, Super-Tack Polyester Resin RHER4BL 4 12
Resin RHER4WH 4 12
Component labels, Tamper-Evident Polyester Resin RHER4BL 2 12
Component Labels, Tedlar Resin RHER4BL 4 12
Component Labels, Vinyl Cloth Hybrid RHEH4BL 4 9
Continuous Tape, Photoluminescent Polyester Resin RHER4BL 4 12
Continuous Tape, Polyolen Resin RHER4BL 3 8
Continuous Tape, Reective Resin RHER4BL 4 4
Continuous Tape, Standard Polyester Resin RHER4BL 4 10
Continuous Tape, Super-Tack Polyester Resin RHER4BL 4 8
Continuous Tape, Vinyl Resin RHER4BL 4 8
Resin RHER4WH 4 12
Heat Shrink, 1-sided Military grade Hybrid RHEH4BL 4 4
Resin RHER4WH 3 10
Heat Shrink, 2-sided Fluid Resistant Resin RHER4BL-C 4 10
Heat Shrink, 2-sided Halogen Free Hybrid RHEH4BL 4 10
Heat Shrink, 2-sided Military Grade Hybrid RHEH4BL 4 8
Marker Plates, Flame Retardant, Halogen Free Resin RHER4BL 4 12
Marker Plates, Flame Retardant, High Temp Resin RHER4BL-A 2 15
Marker Plates, Standard Resin RHER4BL 4 11
Wire Labels, Flag Resin RHER4BL 3 10
Wire Labels, Non-Laminated, Nylon Cloth Resin RHER4BL 4 8
Wire Labels, Non-Laminated, Vinyl Cloth Hybrid RHEH4BL 4 8
Wire Labels, Self-Laminating, PVDF Hybrid RHEH4BL 4 12
Wire Labels, Self-Laminating, Vinyl Hybrid RHEH4BL 4 10
Resin RHER4WH 2 12
Wire Labels, Turn-Tell Hybrid RHEH4BL 4 10
TDP43HE PRINTER RIBBON SETTING
RECOMMENDATIONS
B20747
Rev. 01 Page: 2 of 3 04JUN2015
NOTES:
1) For most media types, the recommended Printhead Pressure Settings (see User Manual, Section 2.7.1) are as
follows:
Liner width greater than 2" ---------> Left = 1 Right = 1
Liner width less than 2" ---------> Left = 5 Right = 1
2) With Black Single-sided Heat Shrink, the “MANUAL” Gap Calibration option (on-printer menus) must be used.
See User Manual, Section 3.1.3-2, for detailed instructions.
3) For some print jobs, the user might wish to fine tune the placement of the print, on the actual label. For these
occasions, we recommend the use of the “Features” button, located in the Easy-Mark print window (see
below). In the “Print Offsets” section, a positive “Top” offset will shift the print down, and a negative offset will
shift the print up. A positive “Left” offset will shift the print right, and a negative offset will shift the print left.
If the “Top” offset is not able to move the print far enough, vertically, there is another option. Instead, the user
can adjust the “Label Offset” value, within the “Advanced Setup” tab of the printer “Properties”:
TDP43HE PRINTER RIBBON SETTING
RECOMMENDATIONS
B20747
Rev. 01 Page: 3 of 3 04JUN2015
4) Raised Panel labels, with a height less than 1”, will cause a misprint (legend too low) on the first label of a print
job. To correct this issue, the user can disable the post-print action (select “None” instead of “Tear o”) within
the Advanced Setup tab of the printer “Properties”.
Website: www.panduit.com
Email: id-support@panduit.com
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com
Technical Support:
Panduit Corp. • ID Products Division
Cumming, GA
Tel: 800-777-3300 • Fax: 708-532-1811
Panduit Europe • EMEA Service Center
Almelo, Netherlands
Tel: +31-546-580-452 • Fax: +31-546-580-441
Panduit Europe • West World Headquarters
Westgate, London
England Tel: 208-601-7200 • Fax: 208-601-7319
Specyfikacje produktu
| Marka: | Panduit |
| Kategoria: | drukarka |
| Model: | TDP43HE |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Panduit TDP43HE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje drukarka Panduit
28 Grudnia 2024
24 Września 2024
15 Września 2024
10 Września 2024
9 Września 2024
8 Września 2024
8 Września 2024
8 Września 2024
Instrukcje drukarka
- drukarka LG
- drukarka Middle Atlantic
- drukarka Pantum
- drukarka Nilox
- drukarka Datamax O'Neil
- drukarka Argox
- drukarka Equip
- drukarka D-Link
- drukarka Raspberry Pi
- drukarka IDP
- drukarka Ultimaker
- drukarka Custom
- drukarka Kodak
- drukarka Intermec
- drukarka Videology
Najnowsze instrukcje dla drukarka
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025