Instrukcja obsługi Planet IGS-510TF
Planet
Niesklasyfikowane
IGS-510TF
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet IGS-510TF (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Compact Industrial 4-Port
10/100/1000T + 1-Port 100/1000X SFP Gigabit Ethernet Switch,
IGS-510TF. In the following sections, the term “Industrial Gigabit
Ethernet Switch” means the IGS-510TF.
Open the box of the Industrial Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Industrial Gigabit
Ethernet Switch x 1
User’s Manual x 1 Wall-mount Kit x 1
DIN-rail Kit x 1 RJ45 Dust Caps x 4 SFP Dust Cap x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
Switch Fabric 10Gbps
Throughput
(packet per
second)
7.4Mpps@64bytes
Address Table 2K entries
Buer Memory 4M bits on-chip buer memory
Jumbo Frame 9Kbytes
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3az Gigabit SX/LX
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy Ecient Ethernet (EEE)
IEEE 802.1p Class of Service
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
Note
The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
Note
1. The power input range is 9V ~ 48V DC for Indus-
trial Gigabit Ethernet Switch and supports 24V AC
2. Use one power input when using 24V AC.
3.5 Grounding the Device
Users MUST complete grounding wired with the device; otherwise,
a sudden lightning could cause fatal damage to the device.
Max. Fault Alarm Loading: 24V, 1A
V1+
V2+
PWR1
PWR2Alarm
DC Input: 9-48V
, 0.28A max.
AC Input: 24V
, 0.3A max.
1 2 3 4 5 6
Earth Ground
Note
EMD (Lightning) DAMAGE IS NOT COVERED UNDER
WARRANTY.
3.2 LEDDenition:
LED Color Function
P1 Green Lights to indicate power input 1 has power.
P2 Green Lights to indicate power input 2 has power.
1000
LNK/ACT
Green
Lights to indicate the port is running at
1000Mbps speed and successfully established.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
10/100
LNK/ACT
Amber
Lights to indicate the port is running
at 10/100Mbps speed and successfully
established.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
3.3 Switch Upper Panel
The upper panel of the Industrial Gigabit Ethernet Switch consists
of one terminal block connector within two power input.
V1+
V1-
PWR1
V2+
V2-
PWR2
DC Input: 9-48V , 0.6A max.
AC Input: 24V , 0.3A max.
1 2 3 4
Figure2: IGS-510TF Top View
2.ProductSpecications
Model IGS-510TF
Hardware Specications
Copper Ports
4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X
ports
SFP Slot
1 1000BASE-SX/LX/BX SFP interface
compatible with 100BASE-FX SFP
Connector
Removable 4-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for Power 2
Power
Requirements
9~48V DC, redundant power with reverse
polarity protection, 24V AC power support
Power
Consumption
(Ethernet Full
Loading)
Max. 2.4 watts/8.1BTU
Dimensions
(W x D x H)
70 x 104 x 30 mm
Weight 239g
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV
EFT Protection 6KV
Switch Specications
Switch
Architecture
Store-and-Forward
3. Hardware Introduction
3.1 Switch Front Panel
The front Panel of the Industrial Gigabit Ethernet Switch consists of
Ethernet interfaces and LED indicators.
Front View
5
P1 P2
1
2
3
4
IGS-510TF
ACTLNK
ACTLNK
1000
10/
100
Figure1: IGS-510TF Front View
3.4 Wiring the Power Inputs
The terminal block connector on the top panel of Industrial Gigabit
Ethernet Switch is used for two redundant power inputs. Please
follow the steps below to insert the power wire.
Caution
When performing any of the procedures like inserting
the wires or tightening the wire-clamp screws, make
sure the power is OFF to prevent from getting an
electric shock.
1. Insert positive and negative DC power wires into contacts 1 and
2 for POWER 1, or contacts 3 and 4 for POWER 2.
V1+
V1-
PWR1
V2+
V2-
PWR2
DC Input: 9-48V , 0.6A max.
AC Input: 24V , 0.3A max.
1 2 3 4
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2 3 4
Power 1 Power 2
+ - + -
4. Installation
This section guides you to installing the Industrial Gigabit Ethernet
Switch on the DIN rail and wall. Please read this chapter completely
before continuing.
Note
This following pictures show how to install the device.
However, the device in the picture is not IGS-510TF.
4.1 DIN-rail Mounting Installation
1
2
4.2 Wall-mount Plate Mounting
Specyfikacje produktu
| Marka: | Planet |
| Kategoria: | Niesklasyfikowane |
| Model: | IGS-510TF |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Planet IGS-510TF, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Planet
8 Stycznia 2025
8 Stycznia 2025
8 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
7 Grudnia 2024
7 Grudnia 2024
Instrukcje Niesklasyfikowane
- Pfaff
- Werma
- Netgear
- BRIO
- Pancontrol
- Hercules
- SVS
- MoFi
- Laney
- Baja Mobility
- De Buyer
- Freeplay
- HPRC
- Europalms
- TAURUS Titanium
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025