Instrukcja obsługi Planet IXT-705AT

Planet nieskategoryzowany IXT-705AT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet IXT-705AT (4 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 10.5 użytkowników na średnio 4.2 gwiazdek

Pobierz PDF

Strona 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET Industrial 10G Media Converter.,

In the following section, unless specied, the term “Industrial

Media Converter” mentioned in this manual refers to the

IXT-705AT.

Open the box of the Industrial Media Converter and carefully

unpack it. The box should contain the following items:

Industrial Media

Converter x 1 User’s Manual x 1 DIN-rail Kit

Wall-mount Kit SFP+ Dust Cap x 1 RJ45 Dust Cap x 1

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original

packing material, and use them again to repack the product in case

there is a need to return it to us for repair.

2.ProductSpecications

Model IXT-705AT

Hardware Specications

Copper

Interface

1 x 10000/5000/2500/1000/100 BASE-T RJ45

Auto-MDI/MDI-X, auto-negotiation

Fiber Optic

Interface 1 10GBASE-SR/LR SFP+ interface

Connector

Removable 6-pin terminal block

Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin

5/6 for Power 2

Alarm Provides one relay output for power failure

Alarm relay current carry capacity: 1A @ DC 24V

LED

System:

Fault Alert (Red), PWR (Green)

10000/5000/2500/1000/100 BASE-T RJ45

Interfaces

1/10G LNK (Orange)

5000/2500/100M LNK (Green)

ESD

Protection 6KV DC

Enclosure IP30 type metal case

Installation DIN-rail kit and wall-mount ear

Dimensions

(WxDxH) 32 x 87 x 135mm

Weight 458g

3.3 Converter Upper Panel

The upper panel of the IXT-705AT consists of one terminal block

connector within two DC power inputs. Figure 3-2 shows the upper

panel of the IXT-705AT.

Max. fault loading: 24V, 1A

V1+ V2+

PWR1 PWR2Fault

DC Input: 12-48V

, 0.6A max.

AC Input: 24V

, 0.2A max.

1 2 3 4 5 6

Figure 3-2: IXT-705AT Upper Panel

4. Hardware Installation

This section describes how to install the Industrial Media Converter

and makes connections to it. Please read the following sections and

perform the procedures in the order being presented.

This section describes the functionalities of the Industrial Media

Converter’s components and guides you to how to install it on

the DIN rail and wall. Basic knowledge of networking is assumed.

Please read this chapter completely before continuing.

4.1 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial Media Converter is used for two DC redundant power

inputs. Please follow the steps below to insert the power wire.

3. Hardware Introduction

3.1 Physical Dimensions

IXT-705AT dimensions (W x D x H): 32 x 87 x 135mm

32.00

135.00

87.80

97.10

48.8046.50 39.70

28.00

48.80

53.50 53.50

18.00

15.20

30.00

9.20

40.00

28.0018.00

28.00

18.0028.00

28.00

40.00

Top View

Side View Front View Side View

Mounting Kit

DIN-Rail Kit

Unit: mm

Rear View

Bottom View

10G SFP+

10GBASE-T

2.5G

10G/1G

5G/100

FaultP2 P1

Max. f ault loading: 24V, 1A

V1+ V2+

PWR 1 PWR 2Fault

DC Input: 12-48V

, 0.6A max .

AC Input: 24V

, 0.2A max .

1.1 Product Features

IXT-705AT Physical Port

 1-port 10000/5000/2500/1000/100BASE-T RJ45 with auto

MDI/MDI-X function

 1-port 10GBASE-X SFP+

Layer 2 Features

 IEEE 802.3u/802.3ab/802.3bz/802.3ae Ethernet standard

compliant

 Supports auto-negotiation and 100Mbps half/full duplex and

1/2.5/5/10Gbps full duplex mode

 Prevents packet loss with back pressure (half-duplex) and

IEEE 802.3x pause frame ow control (full-duplex)

 16K jumbo frame size support

 Automatic address learning and address aging

Industrial Case and Installation

 Slim-type IP30 metal case

 DIN-rail or wall-mount design

 Redundant power design

 12 to 48V DC, redundant power with reverse polarity protection

 AC 24V power adapter acceptable

 Supports 6000 VDC Ethernet ESD protection

 100 meters over Cat 6A at 10Gbps

 -40 to 75 degrees C operating temperature

 Plug and Play installation

Power

Requirements DC 12~48V or 24V AC

Converter Specications

Flow Control Back pressure for half duplex

IEEE 802.3x pause frame for full duplex

Fabric 20Gbps

Address Table 9K entries, automatic source address learning and

aging

Jumbo Frame 16K

Network

Cables

10000/5000/2500/1000/100 BASE-T:

Cat5e, 6, 6A, 7 UTP cable (100 meters, max.)

EIA/TIA-568 100-ohm STP (100 meters, max.)

10GBASE-LR/SR/BX:

50/125μm or 62.5/125μm multi-mode ber

optic cable, up to 300m

9/125μm single-mode ber optic cable, up to

60km

Standards Conformance

Standards

Compliance

IEEE 802.3u 100BASE-TX

IEEE 802.3ab 1000BASE-T

IEEE 802.3bz 2.5G/5GBASE-T

IEEE 802.3an 10GBASE-T

IEEE 802.3ae 10Gbps Ethernet

IEEE 802.3x full-duplex ow control

Regulatory

Compliance FCC Part 15 Class A, CE

Stability

Testing

IEC60068-2-32 (Free fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

3.2 Converter Front Panel and LED Indicators

Figure 3-1 shows the front panels of the Industrial Media Converter.

10G SFP+

10GBASE-T

2.5G

10G/1G

5G/100

FaultP2 P1

Figure 3-1:

IXT-705AT

Front Panel

System

LED Color Function

P1 Green

Lit: Power 1 is active

O: Power 1 is inactive

P2 Green

Lit: Power 2 is active

O: Power 2 is inactive

FAULT Red

Lit: indicates either power 1 or

power 2 has no power.

O: No failure

Per 10000/5000/2500/1000/100BASE-T Port

LED Color Function

10/2.5/1G

Green Lit: To indicate that the port

is operating at 2.5Gbps.

Orange Lit: To indicate that the port

is operating at 10/1Gbps.

5G/100M Green

Lit: To indicate that

the port is operating at

5Gbps/100Mbps.

1. Insert positive / negative DC power wires into Contacts 1 and 2

for power 1 or 5 and 6 for power 2.

Max. fault loading: 24V, 1A

V1+ V2+

PWR1 PWR2Fault

DC Input: 12-48V

, 0.6A max.

AC Input: 24V

, 0.2A max.

1 2 3 4 5 6

V1+ V1- V2+ V2-

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

123456

Power 1 Fault Power 2

+ - + -

Note

The wire gauge for the terminal block should be in the

range between 12 and 24 AWG.

Note

1. The DC power input range is 12V ~ 48V DC and

supports 24V AC.

2. Please just use one power input when using 24V

AC.

Specyfikacje produktu

Marka:	Planet
Kategoria:	nieskategoryzowany
Model:	IXT-705AT
Kolor produktu:	Niebieski
Materiał obudowy:	Metal
Wysokość produktu:	135 mm
Szerokość produktu:	32 mm
Głębokość produktu:	87 mm
Waga produktu:	458 g
Technologia łączności:	Przewodowa
Certyfikaty:	FCC Part 15 Class A, CE
Standardy komunikacyjne:	IEEE 802.3ab, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3bz, IEEE 802.3u, IEEE 802.3x
Maksymalna szybkość przesyłania danych:	20000 Mbit/s
Prędkość transferu danych przez Ethernet LAN:	100,1000,2500,5000,10000 Mbit/s
Ilość portów Ethernet LAN (RJ-45):	1
Wewnętrzny:	Nie
Zakres temperatur (eksploatacja):	-40 - 75 °C
Zakres wilgotności względnej:	5 - 95 %
Kod zharmonizowanego systemu (HS):	85176990
Napięcie:	12 - 48 V
Diody LED:	Alarm, Fault, Link, Power
Zakres temperatur (przechowywanie):	-40 - 75 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Stopień ochrony IP:	IP30
Złącze światłowodowe:	SFP+
Maksymalny dystans transferu:	100 m
Długość fali:	- nm
Obsługa funkcji Plug & Play:	Tak
Podpora kontroli przepływu:	Tak
Zgodny z Jumbo Frames:	Tak
Rozszerzenie Jumbo Frames:	16000
Automatyczne MDI/MDI-X:	Tak
Montaż DIN na szynie:	Tak
Liczba portów:	1
Transmisja dwukierunkowa duplex:	Full, Half