Instrukcja obsługi Pro-form PFMC8992
Pro-form
Monitor pracy serca
PFMC8992
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pro-form PFMC8992 (12 stron) w kategorii Monitor pracy serca. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.5 gwiazdek
Strona 1/12
Heart Rate Monitor User’s Guide Model No. PFMC89820
Model No. PFMC89920
Congratulations for purchasing the new AccuRate™
heart rate monitor. To install and use the heart rate
monitor, read and follow all instructions in this
user’s guide. For detailed instructions about using
the heart rate monitor with your exercise equipment,
refer to the user’s manual included with your exercise
equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause unde-
sired operation. Changes or modifications not ex-
pressly approved by ICON Health & Fitness, Inc.
could void the user’s authority to operate this device.
WARNING
If you have an implanted medical device such
as a pacemaker, check with your physician be-
fore using the heart rate monitor.
If you have heart problems, or if you are over 60
years of age and have been inactive, do not use
pulse-driven programs.
If you are taking medication regularly, consult
your physician to find whether the medication
will affect your exercise heart rate.
2
How to Install the Receiver
Before the heart rate monitor can be used, the included receiver must be installed.
To install the receiver in an exercise cycle or an elliptical crosstrainer, refer to the instructions in your exer-
cise cycle user’s manual or elliptical crosstrainer user’s manual. After you have installed the receiver, refer to
pages 10 and 11 of this user’s guide. Note: If you have lost your user’s manual, go to www.iconservice.com on
the World Wide Web, or call toll-free 1-800-999-3756.
To install the receiver in a treadmill, refer to the instructions in your treadmill user’s manual. After you have in-
stalled the receiver, refer to pages 10 and 11 of this user’s guide. Note: If you have lost your user’s manual, go to
www.iconservice.com on the World Wide Web, or call toll-free 1-800-999-3756. If your treadmill user’s manual
does not include instructions for installing the receiver, refer to pages 2 through 9 of this user’s manual.
Pages 2 through 9 include 11 different sections that show how the receiver should be installed in different styles
of treadmills. Find the drawings that most closely resemble your treadmill, and follow the instructions in that sec-
tion to install the receiver. Note: Your treadmill may not look exactly like the treadmills shown in the drawings. If
you have questions, call toll-free 1-800-999-3756.
1. Make sure that the power cord is unplugged. Remove
the indicated Screws from the Console Back (A).
Important: The Screws may be different lengths. Keep
track of which Screws were removed from which holes.
2. Peel the paper off the pad on the bottom of the Receiver
(B). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Base (C) in the indicated location.
A
C
Screws
1
2C
B
Cylinder
3. Connect the included Short Jumper Wire (D) to the wire
on the Receiver (B). Connect the other end of the Short
Jumper Wire to the PULSE 2 or PLS2 jack on the back of
the Console (C). If there is a wire already plugged into
the PULSE 2 jack, unplug it. Note: The other wires in-
cluded with the receiver may be discarded. The Wire Tie
can be used to tie wires, if needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (C) with the Screws. Important: If
the Screws are not put back into the same holes from
which they were removed, the Console will be dam-
aged.
C
PLS2
Jack
PULSE 2
Jack
3
DB
3
1. Make sure that the power cord is unplugged. Remove
the indicated Screws (A) from the Console Back (B).
2. Peel the paper off the pad on the bottom of the Receiver
(C). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Back (B) in the indicated location.
Connect the included Short Jumper Wire (D) to the wire on
the Receiver (C). Connect the other end of the Short
Jumper Wire to the PULSE jack on the back of the Console
(E). Note: The other wires included with the receiver may
be discarded. The Wire Tie can be used to tie wires, if
needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (E) with the Screws (A).
B
E
A
1
2
PULSE
Jack
D
E
C
B
Cylinder
Specyfikacje produktu
| Marka: | Pro-form |
| Kategoria: | Monitor pracy serca |
| Model: | PFMC8992 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Pro-form PFMC8992, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Monitor pracy serca Pro-form
20 Września 2024
12 Września 2024
11 Września 2024
7 Września 2024
6 Września 2024
1 Września 2024
Instrukcje Monitor pracy serca
- Monitor pracy serca ProfiCare
- Monitor pracy serca Sanitas
- Monitor pracy serca Echowell
- Monitor pracy serca Medisana
- Monitor pracy serca Maxxus
- Monitor pracy serca VirtuFit
- Monitor pracy serca BBB
- Monitor pracy serca Christopeit
- Monitor pracy serca Bowflex
- Monitor pracy serca Bushnell
- Monitor pracy serca Garmin
- Monitor pracy serca Polar
- Monitor pracy serca Flow Fitness
- Monitor pracy serca Digi-tech
- Monitor pracy serca Osynce
Najnowsze instrukcje dla Monitor pracy serca
15 Stycznia 2025
11 Stycznia 2025
6 Października 2024
3 Października 2024
1 Października 2024
30 Września 2024
Oregon Scientific AH300E Talking Heart Rate Monitor Instrukcja
28 Września 2024
Oregon Scientific AH300 Talking Heart Rate Monitor Instrukcja
28 Września 2024
Oregon Scientific AH300A Talking Heart Rate Monitor Instrukcja
28 Września 2024
28 Września 2024