Instrukcja obsługi Pro-Ject Amp Box S3 CI
Pro-Ject
system hi-fi
Amp Box S3 CI
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pro-Ject Amp Box S3 CI (5 stron) w kategorii system hi-fi. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.8 gwiazdek
Strona 1/5
INSTRUCTIONS FOR USE
Pro-Ject Amp Box S3 CI
© Pro-Ject Audio Systems Amp Box CI · Revision 4. . · S3 202 05 27
2
Dear music lover,
thank you for purchasing a P -Ject Audio Systems custom integration amplifier. ro
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
Safety instructions
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply. The power cord is
used to disconnect the unit from the mains. Make sure that the power cord is easily accessible at all times.
Never handle the device, the power cord/power supply while your hands are wet or damp.
Avoid letting liquids enter the device or the power supply. Never place any item containing liquid, such
as a flower vase on or near the device. Never spill any liquid on the device or the power supply. Never
place any naked flame sources, such as lighted candles on or near the device. The product shall not be used
in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Connectors
Make all connections whilst the amplifier is disconnected from the mains. Take care to connect the left
and right channels correctly. The right channel is usually marked red, the left channel black or white.
Make sure the polarity of the connection is correct at each end of the cables.
Only connect one loudspeaker with an impedance not less than 4 ohms per channel.
Never use any other power supply than the one supplied with the unit.
Connection to the preamplifier
The Input sockets marked L
L
L
LLeft
eft
eft
efteft
R
R
R
R Rig
ig
ig
igight
ht
ht
htht/ are for connecting the cables from your pre-amp or AV processor. Signal
can be relayed further via RCA output marked
L
L
L
LLoop.
oop.
oop.
oop.oop.
Connection to the speakers
The output terminals accept phoenix connectors. A 4-pin phoenix connector for the speaker outputs is included
in the packaging.
Take care to mount L+/- and R+/- speaker cables wires correctly. + and is usually clearly marked –
on speaker cables.
Mains power connection
Connect the low voltage plug from the power supply to the Powe
Powe
Powe
PowePower
r
r
r r
-
-
-
-- V
V
V
VV
DC
DC
DC
DCDC 20
20
20
2020 24
24
24
2424 phoenix connectors of the
amplifier before connecting the power supply to the mains. A 2-pin phoenix connector for the power supply is
included in the packaging. Mount the -
r
r
r
rred
ed
ed
ed ed PSU cable in the “+” and the blac
blac
blac
blacblack
k
k
k k in the “ “ connectors.
©Pro-Ject Audio Systems Amp Box · Revision 4. .· S3 CI 202 05 27
3
Trigger
The amplifier can be switched on & off via the 12V DC 2,5mm socket marked Tr
Tr
Tr
TrTrigg
igg
igg
iggigger
er
er
er er In
In
In
InIn. Cables are available
as accessories. The remote power-on signal can be relayed to further units via the Trig
Trig
Trig
TrigTrigge
ge
ge
geger
r
r
r r Out
Out
Out
OutOut socket.
Pay attention to the correct polarity of the cable.
RS232 on/off or front panel button on/off can override trigger commands.
Only connect the remote power cable when the pre- and power amplifier are disconnected from the
mains. Failure to observe can result in damage to the circuit.
Signal Sensing
Use the dip switch to turn signal sensing on and off. When turned on, the Amp Box S3 CI turns off
Sig.S
Sig.S
Sig.S
Sig.SSig.Sens.
ens.
ens.
ens.ens.
automatically when no input signal is detected for 3 seconds (less than 4,4mV over 3 seconds), and
automatically powers on as soon as an input signal is detected (threshold of 4,2mV).
When Signal Sensing is , then turning the unit on or off with the front panel button, RS232 or trigger
ON
ON
ON
ONON
will not work.
Auto Power
Set the dip switch to to enable the Amp Box S3 CI to be turned on as soon as it receives power
Auto
Auto
Auto
Auto Auto Pwr
Pwr
Pwr
PwrPwr O
O
O
OOn
n
n
n n
from the connected power supply. The power button on the front panel does not need to be pressed anymore
to turn the Amp Box S3 CI on.
When Auto Power is , then turning the unit on or off with the front panel button, RS232 or trigger
ON
ON
ON
ONON
will not work. Auto Power also overrides signal sensing, the device will always stay on.
RS232
RS232 is a widely used control protocol used in custom integration to remotely control and integrate devices
into a larger system. Home theatre, public address systems, lobby background music, hotels, ….
The RS232 documentation can be downloaded on the product website:
https://www.project-audio.com/en/product/amp-box- -ci/#downloadss3
Front panel controls
To switch on from standby or to standby
The push button on the left side of the front panel turns the unit on or back into standby. The blue LED above
the stand-by push button shows that the unit is switched on.
Specyfikacje produktu
| Marka: | Pro-Ject |
| Kategoria: | system hi-fi |
| Model: | Amp Box S3 CI |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Pro-Ject Amp Box S3 CI, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje system hi-fi Pro-Ject
27 Lutego 2025
11 Stycznia 2025
5 Stycznia 2025
30 Grudnia 2025
27 Grudnia 2024
30 Września 2024
29 Września 2024
29 Września 2024
29 Września 2024
17 Września 2024
Instrukcje system hi-fi
- Geemarc
- Werma
- Arcam
- JK Audio
- MIPRO
- Magnat
- Soundstream
- SoundCast
- BeamZ
- JB Systems
- Samson
- AKG
- Memphis Audio
- Avid
- CSL
Najnowsze instrukcje dla system hi-fi
9 Kwietnia 2025
5 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
29 Marca 2025
28 Marca 2025
28 Marca 2025