Instrukcja obsługi Radial Engineering Bones London
Radial Engineering
Niesklasyfikowane
Bones London
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Radial Engineering Bones London (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.3 gwiazdek
Strona 1/2
True to the Music
1
3
2
7
6
45
10
8
LONDON DISTORTION
OWNER’S MANUAL
Radial Engineering Ltd.
Part # R800 7105
Bones London Distortion
FEATURES AND FUNCTIONS
1. : 1/4" input jack for your guitar.IN
2. : 1/4” output jack connection to your amp.OUT
3. : Connection for 9-12 volt DC (center pin negative ).PSU
4. BYPASS: Footswitch toggles between distortion and clean bypass. An
on/off LED status indicator illuminates when the distortion is active.
5. TOGGLE: Choose between the two output LEVEL controls by depressing
the footswitch. LEVEL-1 is voiced for rhythm guitar while LEVEL-2 is
augmented in the mid-range to increase sustain and cut for solos. An
LED status indicator illuminates when channel-2 is active.
6. : Used to adjust overall amount of distortion.DRIVE
7. : Two-band EQ shapes treble and bass response. HIGH & LOW
8. BITE : Three position BITE switch controls the overall high-end character.
Choose between fl at response ( ), high-end boost ( ) or high-end
cut ( ).
9. KICK: Three position KICK switch is a mid-range control that can be called
upon to add +7dB or +12dB of mid-range boost for sustain.
10. LEVEL 1 & 2: Both channels are equipped with a level control that lets
you adjust the overall output volume of each channel separately. Think of
these like the master volume control on a guitar amplifi er.
CONGRATULATIONS on your purchase of the Bones London distortion.
The London is a solid-state distortion pedal with a multi-stage drive circuit
that produces high-gain tones reminiscent of Plexi-style tube amplifi ers. The
key to this pedal is how well the circuit retains note clarity even when driven
to extreme levels of saturation. Like the English Navy the London Bones will
never get soggy or sink into the mud.
For maximum on-stage effi ciency, the London is confi gured for clean,
rhythm & lead playability. In bypass mode, you get the natural clean sound
of your guitar. When the London is activated, you can select between two
variable LEVEL controls. Use LEVEL-1 to set a volume for rhythm guitar and
LEVEL-2 for soloing. To increase sustain and cut for solos, the second drive
circuit is augmented in the mid-range.
The tone and drive controls work together to deliver a shepherd’s pie of
British tones. The variable DRIVE control lets you dial-in the perfect amount
of distortion and the powerful dual-band equalizer with Radial’s distinctive
passive-interactive circuit shapes the overall sound. A 3-position KICK
switch can add extra mid-range drive or fatten up single coil pickups. A 3-
position BITE switch controls high-end character of the sound and lets you
compensate for overly bright amps or add extra sizzle.
The London is a high-gain distortion pedal that delivers decades of Plexi-
style sounds in a compact and easy to use format. God save the Queen!
POWERING THE LONDON DISTORTION
Bones pedals require an external power adapter that outputs 9 to 12 volts
DC with a 2.1mm barrel jack wired center pin negative
. Bones
pedals will draw a max of 100mA. Possible damage may occur if another
type of power adapter is used. Consult your dealer for more information.
CONNECTIONS AND SETUP
Before you begin, turn your guitar amplifi er OFF. Connect the power supply
adaptor. The LEDs illuminate when a footswitch is depressed indicating the
pedal is powered up and ready for use.
To start, place the pedal in bypass mode by
depressing the BYPASS footswitch (LED
off) and set the controls as pictured. This will
give you a good starting sound while getting
to know your London distortion.
Connect your guitar to the IN jack.
Connect the OUT jack to your amplifi er.
Always test your connections with your amp set at a low volume level. Turn
your amp on. If no sound is heard check the guitar and power connections.
Turn your amp up to a comfortable playing level. While in bypass mode set
up your clean (or not so clean) sound on your amp.
Activate the pedal by depressing the BYPASS footswitch (LED on). Select
channel-1 by depressing the TOGGLE footswitch (LED off). Adjust the
LEVEL-1 control so the volume is a little louder than the bypassed volume.
Depress the TOGGLE footswitch again and set up the LEVEL-2 control a
little louder for solos and you’re ready to rock.
You will fi nd that most of the controls are intuitive and extremely sensitive
to changes. Small control adjustments will make big changes in the sound.
Take your time, experiment and have fun.
9
TM
Specyfikacje produktu
| Marka: | Radial Engineering |
| Kategoria: | Niesklasyfikowane |
| Model: | Bones London |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Radial Engineering Bones London, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Radial Engineering
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
21 Grudnia 2024
Instrukcje Niesklasyfikowane
- Brizo
- Fritel
- Spring
- Dostmann Electronic
- Cresta
- Daitsu
- Comark
- Mamas & Papas
- Herlag
- Kärcher
- Extron
- DataVideo
- Archos
- Exelpet
- Infinity
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025