Instrukcja obsługi Rio TABK

Rio nieskategoryzowany TABK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Rio TABK (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/2

MAKING YOUR OWN STENCIL

Using self-adhesive paper, ﬁnd a design

you like - a simple shape works best.

Place stencil material over picture. Trace

around image.

Cut away the pieces using a sharp blade.

IMPORTANT: Remember the bits that you cut away will be

coloured sections on your skin when you spray the design.

REMOVING TATTOOS

Most make up removers or soap and water will remove your

tattoo.

USEFUL TIPS

• Avoidwashingtattoo.

• Avoidfrictionwithclothes,asthiswillreduceitslifespan.

• EnsurethatyoushaketheBodyInkbottlevigorously

before use.

• Shavetheareawherethetattoowillbeapplied.

• Coveryourtattoowhenshoweringorbathing.Clinglmis

particularly useful.

• Applyingalightcoatingoftalcumpowderwillensurethat

your tattoo is completely dry. It will also prolong its life.

• Youcantidyuptheedgesofyourtattoowithacottonbud

and make-up remover or soap and water.

• AftereachsessiontaketheBodyInkbottleoffthe

Airbrush and wash Airbrush, Nozzle and Feeder Tube

inwarmwater.BlowjustwaterthroughtheAirbrushto

remove any residual ink.

T R O U B L E S H O O T I N G

THERE IS GAS BUT NO COLOUR SPRAYING THROUGH

THE AIRBRUSH.

1. Using a pin, check the two small breather holes in the bot-

tle Nozzle are not blocked. If you cannot unblock them,

either wash the Nozzle or use a new one.

2.TurntheFlowAdjustmentclockwisetoallowmorecolour

to ﬂow.

3. The Airbrush Nozzle may be blocked. Try turning the Flow

Adjustorfullyclockwiseandthenanti-clockwise.

4. Ensure you have ﬁtted the Feeder Tube to the Nozzle.

5. The Airbrush may need cleaning.

THERE IS LITTLE GAS AND NO COLOUR SPRAYING

THROUGH THE AIRBRUSH.

This means the CO2 Gas Canister is low in pressure, either

from continuous spraying or because it is running out.

1. If you have been spraying continuously this lowers the gas

pressure. Leave the Airbrush for 10-15 minutes for the

pressure to recover.

2. If, after 10-15 minutes, the pressure has not recovered,

change the CO2 Gas Canister for a new one.

NOTE: If opening the Airbrush with a CO2 Gas Canister in

place, the CO2 gas will escape through the vent in the base

of the Airbrush. This can be very cold and care should be

taken to avoid holding the Airbrush at this point.

THE AIRBRUSH HAS BECOME NOISY DURING USE.

ThisisnormalandistheregulatoradjustingtheCO2 pressure.

THE TATTOO ISN’T DRYING VERY WELL.

This means the application of colour is too thick.

1. Turn the Flow Adjustor anti-clockwise to reduce the

colour ﬂow.

2. Try spraying further away.

3.Remember to shake the Body Ink bottle before use,

it is common for the colour to separate slightly.

4. Ensure the Airbrush is kept moving while spraying.

THE COLOUR HAS RUN UNDER THE STENCIL.

This probably means the colour has been sprayed too thickly.

1.TurntheFlowAdjustoranti-clockwisetoreducethecolour

ﬂow.

2. Try spraying further away. Remember to spray between

3-6 cm away from the skin.

3. To remove the excess colour from the stencil, wipe lightly

with some tissue and wait for any remaining colour to dry.

4. Ensure the stencil is pushed ﬁrmly against the skin.

MY TATTOO LOOKS DULL.

More than 1 layer of colour may be required to bring out the

true colour of your tattoo. For example, if you have naturally

pale skin you may require two applications. Alternatively, if

you are dark skinned then you may need to apply 2-3 layers

of the ink to show the true colour. Each layer should be

sprayed very ﬁnely, allowing 3-4 minutes for the ink to dry.

You must build up the colour.

PRECAUTIONS

• Thisproductisnotatoyandshouldnotbeused

without adult supervision. This product is not for use

by children under the age of 12 years. Keep out of the

reach of children.

• DoNOTapplybodyinktoopencutsorbrokenskin

• Nottobetakeninternally.

• DoNOTspraytowardsface.Avoidcontactwitheyes.If

contact with eyes is made rinse immediately with cold water.

• DoNOTbreathevapours,useinawellventilatedarea.

• BlackBodyInkwillstainfabrics.Pleasetakecaretoprotect

your clothes and surrounding work area.

W A R N I N G S

F O R C O

G A S C A N I S T E R S

• Pleaseuseinaccordancewithinstructions.

• Non-aerosol.Non-Rellable.Recyclablesteelonlywhen

empty.

• Contains16gmCarbonDioxide(E290)underpressure.

• Grossweight-58g.Volume20cm3.

• Neverdisposeoffullcartridges.

• DoNOTpierce,incinerateorburn,evenafteruse.

• Explosiondanger-50˚Cmaxtemperature.

1-IN-TABK-UK/1.2

TATTOO

ARTIST

™

CUSTOMER CARE

If you have any questions, or if you experience any difﬁculties with this

product, please call our Rio Careline on 01242 702345

or email us at: online@riobeauty.com

Rio,Dezac,andTattooArtist,aretrademarksofTheDezacGroupLtd

©TheDezacGroupLtd2011.POBox17,Cheltenham,GL537ET,UK

www.riobeauty.com

1-IN-TABK-UK/1.2

APPLICATION

Your tattoo lasts longer if you exfoliate

your skin ﬁrst. Removing dead skin helps

prevent the tattoo from ﬂaking.

Choose your design.

Clean skin. Ensure all dirt, oils and

moisturisers are removed.

Remove the Stencil from the backing sheet,

and apply to the skin.

Hold the Airbrush 15-20 cm (6-8") away

fromstencil.ApplyaVERYLIGHTlayerof

ink in a short burst.

IMPORTANT: Applying too much ink may

cause seepage under the stencil edge.

Allow ink to dry. You may wish to use a

hairdryer to speed the process up. Apply

a second or third coat if necessary. Peel

off stencil.

Remove overspray with luke warm water or

an alcohol based cleanser.

Apply a small amount of Fixing Powder to

cover and protect your tattoo.

Now go out and show off your tattoo!

NOTE: The self adhesive stencil is effective for several

uses if returned carefully to its backing sheet after use. If

adhesiveness wears off, use the stencil glue supplied.

COMPONENTS

PATCHTEST

Patch test the body ink on a small area of your skin 24 hours

before use. If irritation occurs discontinue use. Only use inks

supplied by Rio.

TECHNIQUE

Pressing the trigger releases the air and

sprays colour out. Spray test onto a sheet

of paper.

REDUCING COLOUR FLOW

TurntheFlowAdjustoranti-clockwise.

Reduce the colour ﬂow until you have a ﬁne

spray.Buildupthinlayersofcolour.This

technique also shortens the drying time.

INCREASING COLOUR FLOW

TurntheFlowAdjustorclockwise.

IMPORTANT: For best results, spray in VERY short bursts.

It is important to have a ﬁne spray of colour to achieve a

professional ﬁnish. If your results are not smooth, reduce

the colour ﬂow and aim to build up the colour in several very

ﬁne layers. Clean the Airbrush, Nozzle and Feeder Tube in

warm water and dry completely after use.

PREPARATION

Shake the Body Ink VIGOROUSLY for at

least 30 seconds.

Remove cap and push a Feeder Tube ﬁrmly

into a Nozzle.

Screw onto the bottle.

Attach the Flow Adjustor to the Body Ink

bottle.

Unscrew the Airbrush.

Place the CO2 Gas Canister in the bottom

half of the Airbrush.

Screw the top of the Airbrush fully down

until top and bottom meet. This pierces

the Canister to release the gas into the

Airbrush.

NOTE: If the Airbrush is opened after this

point all the gas will escape and a new

Canister will be needed.

Attach the Flow Adjustor to the Airbrush

by slotting it into place. Check the Flow

Adjustorisopen.

DO NOT twistthe FlowAdjustor when slottinginto place.

This can break the retaining ﬁngers.

CLEANING

Turningthe Flow Adjustor fully bothways

will help to dislodge any dry colour in the

Airbrush Nozzle.

Unblock Nozzle breather holes using a pin.

Detach Tube. Thoroughly wash Flow

Adjusters, Nozzles and Feeder Tubes in

warm water.

CLEANING STENCILS

With the stencil on its backing sheet, use warm water and

a little detergent on a cloth or cotton wool to wash off the

colour. Allow to air dry.

UNBLOCKINGAIRBRUS H

If the Airbrush becomes blocked:

1. Dismantle the Airbrush, separating the Flow Adjustor

fromtheCentralSpindle/CentreHole.

2. DetachtheCentralSpindlefromtheBottleNozzle.

3. Clean all surfaces in warm water with liquid detergent to

remove any residue.

4. EnsurethattheCentreHoleantypedCrossHoleinthe

CentralSpindleareclear.(Anoldtoothbrushcanbea

usefultool).

5. Rinse all parts with clean water and dry. To ensure all

blockages have been removed, blow through the Central

SpindleandtheFlowAdjustor.

6. Reassemble the Airbrush in reverse order.

6. CO2GasCanisters(x3)

7. Nozzles(x2)

8. FixingPowder

9. BlackInks(x2)

10. Stencil Glue

1. Self-Adhesive Stencil Pack

2. Airbrush

3. Stand

4. FlowAdjustors(x2)

5. FeederTubes(x2)

18 9

4 5

333

2 2

1 1

Cross

Hole

Flow

Adjustor CentralSpindle/

CentreHole

Specyfikacje produktu

Marka:	Rio
Kategoria:	nieskategoryzowany
Model:	TABK
Zalecany wiek (min):	12 lat(a)
Klej:	Tak
Wzory w zestawie:	Tak
Kolor tuszu:	Czarny
Objętość atramentu:	15 ml

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Rio TABK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje nieskategoryzowany Rio

26 Czerwca 2024

26 Czerwca 2024

26 Czerwca 2024

26 Czerwca 2024

26 Czerwca 2024

26 Czerwca 2024

Rio Salon eyelash extensions Instrukcja

26 Czerwca 2024

Rio DCWH7 Instrukcja

26 Czerwca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024

Emko EZM-9920 Instrukcja

27 Października 2024

Emko ESM-3712-H Instrukcja

27 Października 2024

Emko ATS-10 Instrukcja

27 Października 2024

Emko EAOM-11.2 Instrukcja

27 Października 2024

Emko EPM-3790 Instrukcja

27 Października 2024

Emko EPM-7790 Instrukcja

27 Października 2024

Livarno Lux IAN 108340 Instrukcja

27 Października 2024

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024