Instrukcja obsługi Roland C-80

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roland C-80 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 7 użytkowników na średnio 4.9 gwiazdek

1

Digital HarpsichordDate: Sep. 1, 1998

C-80Version 1.00MIDI IMPLEMENTATION

1.Receive data

■Channel Voice Messages

●Note o

Status2nd byte3rd byte

8nH kkH vvH

9nH kkH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

kk = note number: 00H-7FH (0-127)

vv = note o velocity: 00H-7FH (0-127)

●Note on

Status2nd byte3rd byte

9nH kkH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

kk = note number: 00H-7FH (0-127)

vv = note on velocity: 01H-7FH (1-127)

*Note numbers outside the range of 11-106 are transposed to the nearest octave within

this range.

*Transpose function does not aect the recognized note numbers.

●Control Change

*The value specied by a Control Change message will not be reset even by a Program

Change, etc.

❍Data Entry (Controller number 6, 38)

Status2nd byte3rd byte

BnH 06HmmH

BnH 26HllH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm, ll = the value of the parameter specied by RPN

*Data entry messages are recognized only when received on the basic channel.

❍Volume (Controller number 7)

Status2nd byte3rd byte

BnH 07HvvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Volume: 00H-7FH (0-127), Initial Value = 7FH (127)

*Received volume messages aect received note event levels, and cannot aect internal

keyboard notes.

❍Expression (Controller number 11)

Status2nd byte3rd byte

BnH 0BHvvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Expression: 00H-7FH (0-127), Initial Value = 7FH (127)

*These message can aect only MIDI notes.

❍Hold 1 (Controller number 64)

Status2nd byte3rd byte

BnH 40HvvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON

*These message can aect only MIDI notes.

❍RPN MSB/LSB (Controller number 100, 101)

Status2nd byte3rd byte

BnH 65HmmH

BnH 64HllH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm = upper byte of parameter number specied by RPN

ll = lower byte of parameter number specied by RPN

*The value specied by RPN will not be reset even by messages such as Program Change

or Reset All Controller.

*RPN messages are recognized only when received on the basic channel.

**RPN**

The RPN (Registered Parameter Number) messages are expanded control changes, and each

function of an RPN is described by the MIDI Standard.

To use these messages, you must rst use RPN MSB and RPN LSB messages to specify the

parameter to be controlled, and then use Data Entry messages to specify the value of the

specied parameter. Once an RPN parameter has been specied, all Data Entry messages

received on that channel will modify the value of that parameter. To prevent accidents, it is

recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have nished

setting the value of the desired parameter.

On the C-80, RPN can be used to modify the following parameters.

RPNData entry

MSB LSBMSB LSBExplanation

00H 01HmmH llHMaster Fine Tuning

mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.99

cents), Initial Value = 40 00H (+/-0 cent)

7FH 7FH--- ---RPN null

Set condition where RPN is unspecied. The

data entry messages after set RPN null will be

ignored. (No Data entry messages are required

after RPN null).

Settings already made will not change.

mm, ll: ignored

Copyright © 1999 ROLAND CORPORATION

All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

Specyfikacje produktu