Instrukcja obsługi Schneider MTN648704
Schneider
nieskategoryzowany
MTN648704
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Schneider MTN648704 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 23 osób i została oceniona przez 12 użytkowników na średnio 4.8 gwiazdek
Strona 1/2
The blind actuator REG-K/4x24/6 with manual mode
(referred to below as the actuator) can control up to
four blind drives with limit switch independently of one
another.
You can switch the actuator to manual operation and
check that it works even without ETS programming, and
you can control the connected loads directly at the
actuator in the event of a bus failure.
For your safety
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR
ARC FLASH
Safe electrical installation must be carried out only by
skilled professionals. Skilled professionals must prove
profound knowledge in the following areas:
• Connecting to installation networks
• Connecting several electrical devices
• Laying electric cables
• Connecting and establishing KNX networks
• Safety standards, local wiring rules and regulations
Failure to follow these instructions will result in
death or serious injury.
RISK OF FATAL INJURY FROM ELECTRIC SHOCK
The output may carry electrical current even when the
load is switched off.
• When working on the device: Always disconnect the
device from the supply by means of the fuse in the in-
coming circuit.
• Even if the manual switch is in the „OFF“ position, a
KNX telegram can switch the connections to being
live at any time. Before working on the device, always
diconnect the fuse in the incoming circuit from the
supply.
Failure to follow these instructions will result in
death or serious injury.
The device may be damaged!
• Always operate the product in compliance with the
specified technical data.
• Only connect one motor per channel.
• Only install devices with at least basic insulation next
to the device.
Failure to follow these instruction can result in
equipment damage.
Blind actuator introduction
The actuator has a bus coupler. It is installed on a DIN
rail, with the bus connection made via a bus connecting
terminal. It is supplied with power from the bus voltage.
A data rail is not required.
AProgramming button and programming LED (red)
BUnder the cable cover: Bus connecting terminal
COperating LED "RUN" (green)
DManual operation LED "Manual" (red)
EManual operation key "Manual"
FChannel terminals for loads
GSupply voltage for loads
HChannel keys for manual control of the
corresponding channel, only respond when manual
operation is switched on
IChannel status LEDs (yellow) for the corresponding
channel
When and how the LEDs light up
1Set the actuator onto the DIN rail.
Connections, displays and operating
elements
RUN (green) lights up during normal operation
Manual (red) lights up during manual operation
Channel (yellow) lights up during movement
Mounting the actuator
The device may be damaged!
• Connect the bus connection and the supply voltage
with correct polarity.
• Connect the bus voltage first and only then the load
voltage.
• Protect the switch contacts with a series-connected 6
A circuit breaker.
• Only install devices with at least basic insulation next
to the device.
Failure to follow these instruction can result in
equipment damage.
1 2
1 2
1 2
1 2
Hand
3 4
3 4
3 4
3 4
1 / 3
2 / 4
1
2
3
4
+ + - -
+ + - -
B
C
D
E
I
H
G
A
F
2
1
3
2Connect KNX.
3Connect the bus voltage.
4Wait at least 30 seconds.
After the bus voltage has been switched on, all the
actuator relays are moved to a predefined position
(factory setting: "Off").
5Connect the load.
6Connect the load voltage.
Now you can check the functionality of the actuator and
the connected loads without having to load the
application from the ETS. (See the "Manual operation"
section.)
1Press the programming button.
The programming LED lights up.
2Load the physical address and application into the
device from the ETS.
The programming LED goes out.
The operating LED lights up: The application was loaded
successfully, the device is ready for operation.
Normally, you control the blinds using push-buttons or
by remote control. However, you can also switch the
actuator to manual operation and then raise or lower
each blind manually using its channel keys. In order to
be able to do this, the ETS parameter "Manual operation
enabled" must be set to "enabled" and bus voltage must
be present.
Manual operation before downloading the
application for the first time
Immediately after the initial installation, you can switch
the actuator to manual operation, e.g. in order to test
the drives.
Manual operation with the ETS setting "Bus and
manual operation"
In manual operation, the actuator also responds to KNX
telegrams. The command last received is given priority.
If the toggle times are too short, the blind motor
could be damaged.!
• The toggle time at the factory setting is 500 ms. A
longer toggle time may be necessary for other mo-
tors. Refer to the manufacturer's specifications in the
data sheet for the motor.
Failure to follow these instruction can result in
equipment damage.
Putting the actuator into operation
Manual operation
5 mm
1 2
3 4
KNX
1 2
24 V
+ + - -
1 / 3
+ + - -
2 / 4
6A 6A 6A
+
-
SpaceLogic KNX
Blind actuator REG-K/4x24/6 with manual
mode
Operating instructions
Art. no. MTN648704
en
Hand
Specyfikacje produktu
| Marka: | Schneider |
| Kategoria: | nieskategoryzowany |
| Model: | MTN648704 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Schneider MTN648704, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany Schneider
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
13 Sierpnia 2024
29 Maja 2024
23 Maja 2024
9 Maja 2024
Instrukcje nieskategoryzowany
- Hegel
- WyreStorm
- Gefen
- Finlux
- Easy Home
- Dymo
- JennAir
- Crosscall
- Faworyt
- Zoofari
- Flama
- Vivotek
- Stanley
- Linksys
- Char-Broil
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024