Instrukcja obsługi StarTech.com PEX1P2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla StarTech.com PEX1P2 (2 stron) w kategorii drukarka. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 7 użytkowników na średnio 4.9 gwiazdek

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: September 11, 2020

Product Diagram (PEX1P2)

Front Angle View

PortFunction

1Parallel Port • Female DB-25 Parallel Port

2Bracket

• Congurable for and Full Prole Low Height

installations

3PCIe p1-x1 Connector

• Connect the to the Parallel Adapter CardPCI

Express SlotComputer in the

Requirements

For the latest requirements, please visit:

www.startech.com/PEX1P2.

• Computer with an available PCI Express slot (x1)

Tools

• Small Phillips Head Screwdriver

Hardware Installation

Warning: Parallel AdapterCards can be damaged by static electricity. Make sure

that the is properly grounded before they open the or touch InstallerComputer Case

the . The should wear an when Parallel Adapter Card InstallerAnti-Static Strap

installing any computer component. If an is not available, discharge Anti-Static Strap

any built-up static electricity by touching a large for several Grounded Metal Surface

seconds. Only handle the by its edges and do not touch the Parallel Adapter Card

gold connectors.

1 Port PCI Express Dual Prole Parallel Adapter Card - SPP/EPP/ECP®

Installing the Low Prole Bracket

By default the is attached to the . Full Prole BracketParallel Adapter Card

Depending on the system conguration it may be necessary to remove the Full Prole

BracketLow Prole Bracket and replace it with the (included).

1. Using a , remove the two securing Small Phillips Head ScrewdriverBracket Screws

the to the .Full Prole BracketParallel Adapter Card

2. Align the on the with the on the Screw HolesParallel Adapter CardScrew Holes

Low Prole BracketParallel Adapter Card. Making sure the is sitting on-top of the

Screw HolesLow Prole Bracket on the .

3. Insert the through the and into the Bracket ScrewsParallel Adapter CardScrew

HolesLow Prole Bracket on the .

4. Using the , tighten the being Small Phillips Head ScrewdriverBracket Screws,

careful not to over-tighten.

Installing the Parallel Adapter Card

1. Turn o the and any that are connected ComputerPeripheral Devices

(e.g. printers, external hard drives, etc.).

2. Unplug the from the rear of the and disconnect any Power CableComputer

Peripheral Devices that are connected.

3. Remove the from the . CoverComputer Case

Note: Consult the documentation that came with the for details about Computer

how to do this safely.

4. Locate an open (x1) and remove the corresponding PCI Express SlotMetal Cover

PlateComputer CaseMetal Cover Plate from the rear of the . In most instances, the

is attached to the rear of the with a single . Save this Computer CaseScrewScrew

for the next step.

5. Gently insert the into the open and fasten Parallel Adapter CardPCI Express Slot

the to the rear of the using the from step 4. BracketComputer CaseScrew

6. Place the back onto the . CoverComputer Case

7. Reconnect the to the rear of the .Power CableComputer

8. Reconnect all of the that were disconnected in step 2.Peripheral Devices

9. Connect a to the on theSPP/EPP/ECP Peripheral DeviceParallel Port Parallel

Adapter Card.

3

1

2

Specyfikacje produktu