Instrukcja obsługi Supermicro SuperServer AS -2024S-TR
Supermicro
serwer
SuperServer AS -2024S-TR
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro SuperServer AS -2024S-TR (1 stron) w kategorii serwer. Ta instrukcja była pomocna dla 23 osób i została oceniona przez 12 użytkowników na średnio 3.5 gwiazdek
Strona 1/1
http://www.supermicro.com MNL-2431-QRG Rev. 1.0
A+ Server AS -2024S-TR Quick Reference Guide
Front View & Interface Rear View
Hard Drive Installation
Board Layout
No. Description
Slot1- Slot6: PCIe Expansion Card Slots
P0-DIMMA1~P0-DIMMD1 Slots (P0 slots: CPU1)
CPU1
JBT1: CMOS Clear
P0-DIMME1~P0-DIMMH1 Slots (P0 slots: CPU1)
P1-DIMMA1~P1-DIMMD1 Slots (P1 slots: CPU2)
CPU2
P1-DIMME1~P1-DIMMH1 Slots (P1 slots: CPU2)
SATA4-7: Onboard SATA3 Ports
PCIe M.2: M.2 Connector
SUPERDOM1/2: SATA3 DOM Ports (6Gb/s)
SATA0-3: Onboard SATA3 Ports
CN1~2: NVMe Ports
1
2
3
4
5
6
7
8
9
10
11
12
13
Removing a Hot-Swap
Drive Carrier from
the Chassis
1. Press the release button on
the drive carrier, which
will extend the drive
carrier handle.
2. Use the drive carrier handle
to pull the drive out of the
chassis.
Installing a 3.5" Drive
1. Position the drive above the carrier with the PCB side facing down and the connector end
toward the rear of the carrier.
2. Tilt the drive to insert it onto the two posts on the left inside of the carrier.
3. Push the right side of the drive fully into the carrier and allow the two spring locking clasps to
secure the drive.
4. Insert the drive carrier into its bay, keeping the release button on the right. When the carrier
reaches the rear of the bay, the release handle will retract.
5. Push the handle in until it clicks into its locked position
Installing a 2.5" Drive
1.Install the drive directly into the tray with four screws underneath.
2. Insert the drive carrier into its bay, keeping the release button on the right. When the carrier
reaches the rear of the bay, the release handle will retract.
3. Push the handle in until it clicks into its locked position
CPU Installation
Caution
1. Removing the Processor Force Frame
Use a Torx T20 driver to loosen the screws holding
down Force Frame in the sequence of 3-2-1. The
screws are numbered on the Force Frame next to each
screw hole.
2. Raising the Force Frame 3. Lifting the Rail Frame
5. Inserting the Carrier Frame/CPU Package 6. Lowering the Force Frame 7. Securing the Force Frame
Secure the screws in the order 1-2-3, tightening to
16.1 kgf-cm (14 lbf-in) of torque. The Force Frame
secures both the Rail Frame and CPU Package.
Caution: Tightening must be executed in proper
1-2-3 sequence to avoid causing catastrophic
damage to the socket or CPU Package.
8. The Force Frame Secured
1. Mounting the Heatsink
Screw #1
Screw #2
Screw #3
Force Frame
Rail Frame
PnP Cover Cap
Carrier Frame/
CPU Package
Processor Installation
4. Removing the External Cap and PnP
Cover Cap
External Cap
PnP Cover Cap
Heatsink Installation
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning before
connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING:
To reduce risk of electric shock/damage to equipment, disconnect power
from server by disconnecting all power cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
WARNING:
Always be sure all power supplies for this system have the same power
output. If mixed power supplies are installed, the system will not operate.
For more information go to : http://www.supermicro.com/support
!
!
!
2.5" Drive 3.5" Drive
CPU1 CPU2
#1 Screw (hidden)
#3 Screw
#4 Screw
#2 Screw
2. Securing the Heatsink
Using a diagonal pattern and a Torx T20 driver, tighten the four
heatsink screws evenly to 16.1 kgf-cm (14.0 lbf-in) torque.
Air Shroud Installation
1. Power down the system.
2. Extend the server from the rack (or remove it and
place it on a bench), then remove the cover
as described previously.
3. Place the air shroud over the DIMM slots
and CPUs as illustrated below.
The small tabs on the air shroud fit
into corresponding reception points
in the horizontal frames behind the
fans and at the rear of the
chassis.
4. Once installed, replace the
cover and push the system
back into the rack before
restoring power.
* Twelve 3.5"/2.5" hot-swap drive bays: default configuration supports up to eight
SATA (slot 4-11) and four NVMe drives (slot 0-3)
** SAS support requires optional add-on card and cables
Power Button
Reset Button
Power LED
LAN1 and LAN2 LED
Power Failure LED
1
2
3
4
5
No. Description
HDD Activity LED
Universal Information LED
Service/Asset Tag with
System Serial Number and
BMC Unique Password
Drive Device Status LED
Drive Device Activity LED
6
7
8
9
10
No. Description
HDD2
HDD1
HDD0
(NVMe /SATA(slot 0-3) *
/SAS3 )**
HDD5
HDD4
HDD3
(NVMe /SATA(slot 0-3) *
/SAS3 )**
HDD8
HDD7
HDD6
(SATA /SAS3 )* **
HDD11
HDD10
HDD9
(SATA /SAS3 )* **
8
12
RESET
1
6
2
3
4
5 7
4
RESET
10
9DescriptionNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
PCI-E 4.0 p1-x8 Slot (LP)
PCI-E 4.0 p1-x16 Slot (LP)
PCI-E 4.0 p1-x8 Slot (LP)
PCI-E 4.0 p1-x16 Slot (LP)
PCI-E 4.0 p1-x8 Slot (LP)
PCI-E 4.0 p1-x16 Slot (LP)
UID LED (Unit Identifier Button)
VGA Port
2x LAN Ports
USB 0/1/2/3 Ports
Dedicated LAN for IPMI
COM Port
Redundant Power Supply Modules
813 7910 2 112 11 35 46
Memory
The AS -2024S-TR supports up to 4TB of registered ECC DDR4-3200 SDRAM in 16 DIMM slots.
Refer to the table below for additional memory information.
NOTE: To achieve optimal memory performance, the minimum recommended is at least one
DIMM for each channel pair in the system (e g., A, C, E, G).
Memory Support
Processors and their Corresponding Memory Modules
Channel
CPU# D1 C1 B1 A1
2 DIMMs (Not Recommended)
CPU1
CPU1
16 DIMMs
CPU2
4 DIMMs (Not Recommended)
8 DIMMs
CPU1
12 DIMMs (for 7003 CPU only)
CPU1
CPU2
CPU1
CPU2
CPU2
CPU
CPU
CPU
CPU
CPU
CPU
CPU
CPU
CPU
CPU
E1 F1 G1 H1
CPU2 CPU
Handle
Re ease ttl Bu on
Post
Post
Insert this
side first
P0 A1-DIMM
P0 H1-DIMM
S t 3lo
S t 1lo
S t 2lo
S t 4lo
S t 5lo
S t 6lo
P0-DIMMB1
P0-DIMMG1
P0-DIMMC1
P0-DIMMF1
P0-DIMMD1
P0-DIMME1
CPU1
CPU2
P1-DIMME1
P1-DIMMD1
P1-DIMMF1
P1-DIMMC1
P1-DIMMG1
P1-DIMMB1
P1-DIMMH1
P1-DIMMA1
7810 9111213
1 2 3 4 5
6
Specyfikacje produktu
| Marka: | Supermicro |
| Kategoria: | serwer |
| Model: | SuperServer AS -2024S-TR |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Supermicro SuperServer AS -2024S-TR, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje serwer Supermicro
30 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
8 Stycznia 2025
28 Grudnia 2024
28 Grudnia 2024
24 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
Instrukcje serwer
- TAIDEN
- Axis
- Lantronix
- ZyXEL
- Freecom
- Mobotix
- Maxdata
- Opengear
- Matrox
- Atlantis Land
- Flir
- StarTech.com
- Acti
- Gefen
- KanexPro
Najnowsze instrukcje dla serwer
9 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
28 Marca 2025
28 Marca 2025
28 Marca 2025
10 Marca 2025
10 Marca 2025
10 Marca 2025