Instrukcja obsługi Vemer Multitest VE 100 SII
Vemer
Niesklasyfikowane
Multitest VE 100 SII
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Vemer Multitest VE 100 SII (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 11 użytkowników na średnio 4.3 gwiazdek
Strona 1/3
MISURA
E CONTROLLO
281280
Tester for systems check
INSTRUMENT CHARACTERISTICS AND FUNCTIONS
• Voltage, frequency and current measurement
Voltage between L and N
Voltage between L and PE, N and PE, L and N
Voltage between probe and PE
Dispersed current measurement up to 1 A with clamp meter
Operating current measurement up to 150 A with clamp meter
• Dierential protective devices check
Measurement of contact voltage without intervention
Intervention time measurement
Intervention test with nominal fault current
Tests on circuits and dierential switches with increasing fault current
Testsondierentialswitcheswith5•I∆N (10 mA and 30 mA)
Tests on dierential switches suitable for direct pulsating fault currents
Tests on special dierential switches
Test with adjustable fault current
Test of the dierential protection devices in IT systems
• Magnetothermal switches check
Measurement of the impedance of the fault ring and determination
of the short circuit current up to 50 KA
Determination and summary of the suitable magnetothermal switches
• Meters start test
• Circuit impedance measurement
• Earth resistance measurement
• Floor and insulating walls impedance measurement
• Insulating resistance measurement
• Check of the continuity of the earthing and equipotential protection leads
• Phase sequence recording
Code Model Description
VP330500 Multitest VE 100 SII Universal measuring device to check the systems
Universal instrument to check electrical systems in compliance with
the CEI 64-8 standard (LAW 46-90).
Built in compliance with the strictest European standards, it is
equipped with a large display to view the connection diagrams of
each of the selected tests.
By pressing a key once again it also shows the information neces-
sary to make correct measurements (instructions integrated in the
instrument).
All the tests are managed is a simple and straightforward manner
(main functions/subfunctions) by means of two keys.
This allows the measurements requested by the law in force to be
taken for a reliable and fast checking of electric systems.
The Multistamp VE 110 II accessory module enables the storage and
printing of the data recorded and its transfer to a PC, if necessary, to
widen its characteristics further.
Multitest VE 100 SII
• Ease of use:
3 keys to control the instrument:
“MENU” key: to select basic functions and subfunctions
“START” key: to start the measurement cycle
“ I∆N/i” key: for dierential switch intervention
and to access the “ON-LINE” guide
• Printer, memory and interface
• Backlit display
• 9 positions function selector
• Adjustable reading angle
• Socket for battery charger and clamp meter
• Automatic settings, surveillance and switching o
ELECTRIC SYSTEMS CHECK
• 120/230/400 V nominal voltage systems
• 16/50/60/200/400 Hz nominal frequency systems
• User guide instructions integrated in the instrument
• Power supply: 6 1.5 V stilo batteries (IEC LR6) or NiCd or NiMH accumulators
• 3 digits backlit LCD display (70x37 mm) with 128x64 pixel matrix
• Operating temperature: -10 °C ÷ +50 °C
• Storage temperature: -20 °C ÷ +60 °C
• Checks:
- Voltage measurements UL-N
- Voltage measurements UL-PE / UL-L
Concatenated voltage, phases cycle
Voltage measurement between PE and probe
- Frequency measurements
- Continuity of the equipotentials (RL0) polarity automatic inversion
RL0 (polarity + a PE)
RL0 (polarity – a PE)
- Insulation resistance (RISO) 500 V / 250 V / 100 V
- Earth resistance (RE) with and without peg
- Socket measurement without RCD intervention
- Measurement in autorange
- Measurement range: 10 kΩ / 1 kΩ / 100 Ω / 10 Ω
- Dierential test (RCD): 10/30/100/300/500 mA
- Without RCD intervention:
Internal line resistance
Fault ring resistance
- Degree of protection: IP40 instrument, IP40 test point
- Weight: ca. 2.5 kg (with batteries)
- Included accessories
Instructions for use, shoulder strap, case, 2 pole measurement adapter,
3 pole jumper for transformation into adapter, schuko probe adapter,
2 alligator clips, 1 battery set, fuses
REFERENCE STANDARDS
Compliance with Community Directives: 2006/95/EC (Low Voltage) and 2004/108/EC (E.M.C.)
isdeclaredwithreferencetothefollowingstandards:•Safety:EN61010-1•E.M.Compatibility:EN61000-6-4/EN61000-6-1
Specyfikacje produktu
| Marka: | Vemer |
| Kategoria: | Niesklasyfikowane |
| Model: | Multitest VE 100 SII |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Vemer Multitest VE 100 SII, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Vemer
4 Października 2024
3 Października 2024
1 Października 2024
27 Września 2024
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
18 Września 2024
16 Września 2024
Instrukcje Niesklasyfikowane
- Metz Connect
- ProfiCare
- Leef
- ESYLUX
- Kraftmax
- Maxi-Cosi
- Optoma
- Dresden Elektronik
- Dantherm
- Troy-Bilt
- Jedo
- Sony
- Sencys
- CamRanger
- Edouard Rousseau
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025