Instrukcja obs艂ugi Zodiac ZT650
Zodiac
Filtr wody
ZT650
Przeczytaj poni偶ej 馃摉 instrukcj臋 obs艂ugi w j臋zyku polskim dla Zodiac ZT650 (3 stron) w kategorii Filtr wody. Ta instrukcja by艂a pomocna dla 33 os贸b i zosta艂a oceniona przez 17 u偶ytkownik贸w na 艣rednio 5.0 gwiazdek
Strona 1/3
1-4
FUNCTION
INSTALLATION
(Link by Bolt on Valve)
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING
SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE
SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO
BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
WARNING
!
!
4-4
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM,
CLEAN PUMP STRAINER AND SKIMMER BASKETS REGULARLY.
!
FILTER
BACKWASH
RINSE
WASTE
RECIRCULATE
CLOSED
Valve Position
Normal Filtration and Vacuuming
Cleaning Filter by reversing the flow
Used after backwash to flush dirt from valve
By-passes filter, used for vacuuming to waste or lowering water level
By-passes filter for circulating water to pool
Shuts off all flow to filter or pool
Function
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.
!
ZOFI09081122
FUNCTIONS OF VALVE POSITIONS
WASTE
FILTER
BACKWASH RINSE
WASTE
RECIRCULATE
CLOSED
WASTE WASTE
WASTE WASTE WASTE
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
GENERAL
TO ASSEMBLE:
SERVICING VALVE( Stop pump,close gate valve in suction&discharge before proceeding):
a. Set handle in filter position. b. Remove cover screws. c. Lift cover and key assembly out.
1. Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug should align with
flat edge of body screw lug.
2. Position cover o鈥檙ing.
3. Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-tighten.
The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the filter tank and functions as
a permanent dirt removing media. When the control valve is in the FILTER position, the pool water which contains suspended dirt
particles, is pumped through your piping system and is automatically directed by the patented filter control valve to the top of the filter
tank. As the pool water is pumped through the filter, dirt particles are trapped by the sand bed, and filtered out. The cleaned pool water is
returned from the bottom of the filter tank, through the control valve and back to the pool through the piping system. This entire sequence
is continuous and automatic. It provides for total recirculation of pool water through your filter and piping system.
After a period of time, the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes. This means it is time to
clean your filter. With the control valve in the BACKWASH position, the water flow is automatically reversed through the filter so that it
is directed to the bottom of the tank, up through the sand, flushing the previously trapped dirt and debris out the waste line. Once the filter
is back-washed of dirt, set control valve to RINSE position and run pump for about 1/2 to 1 minute, and then set the control valve in the
FILTER position, to resume normal filtering.
NOTE: Turn pump off before changing valve position.
Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are required to install and
service the filter.
1. The filter should be placed on a level concrete slab, very firm ground, or equivalent. The filter should be placed
2. Loading the sand media. Filter sand media is loaded through the top opening of the filter.
a. Loosen the flange clamp and remove filter control valve (if previously installed).
b. Cap internal pipe with plastic cap to prevent sand from entering it.
c. We recommend filling the tank approximately 1/2 way with water to provide a cushion effect when the filter
d. Carefully pour in correct amount and grade of filter sand. (Be sure center pipe remains centered in opening.)
internal pipe.
in the right position so that the piping connections, control valve are convenient and accessible for operation and service.
sand is poured in. This helps protect the under-drain laterals from excessive shock.
Sand surface should be leveled and should come to about the middle of the filter tank. Remove plastic cap from
TITAN SERIES SAND FILTER
ZT800, ZT900Models:ZT700B,
Specyfikacje produktu
| Marka: | Zodiac |
| Kategoria: | Filtr wody |
| Model: | ZT650 |
Potrzebujesz pomocy?
Je艣li potrzebujesz pomocy z Zodiac ZT650, zadaj pytanie poni偶ej, a inni u偶ytkownicy Ci odpowiedz膮
Instrukcje Filtr wody Zodiac
15 Wrze艣nia 2024
15 Wrze艣nia 2024
15 Wrze艣nia 2024
15 Wrze艣nia 2024
14 Wrze艣nia 2024
13 Wrze艣nia 2024
10 Wrze艣nia 2024
8 Wrze艣nia 2024
8 Wrze艣nia 2024
7 Wrze艣nia 2024
Instrukcje Filtr wody
- Billi
- Consul
- Avanti
- ZeroWater
- Sera
- Terraillon
- BRITA
- JBL
- Smeg
- AstralPool
- PUR
- Eldom
- Beemur
- Imetec
- Kent
Najnowsze instrukcje dla Filtr wody
5 Stycznia 2025
31 Grudnia 2025
30 Grudnia 2025
27 Grudnia 2024
26 Grudnia 2024
23 Grudnia 2024
20 Grudnia 2024
19 Grudnia 2024
19 Grudnia 2024
19 Grudnia 2024