Instrukcja obsługi Blebox gateBox
Blebox
Niesklasyfikowane
gateBox
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blebox gateBox (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
Apply the safety systems described in the PN-EN 13241 standard
dening the safety requirements and operational requirements
for gates and barriers.
SAFETY RULES
Connect only in accordance with the diagram presented in the
manual. Improper connections may be dangerous, it can damage
the controller, and loss of the warranty.
Connecting the device to a power supply that does not meet the
quality requirements specied in EN 50081-1, EN 50082-1, UL508,
EN 60950 will invalidate the warranty.
DANGER! Risk of electric shock! Even with the device turned o,
the outputs may be live. All assembly work should be ALWAYS
performed with the disconnected power circuit.
GARAGE, SLIDING AND SWING GATES AND DOOR CONTROLLER
Disconnect the installation supply voltage before installing the controller.
Remember that any mounting works should be carried out when the mains
voltage is disconnected (switch o the mains fuse or disconnect the power
cord from the mains socket).
1
INSTALLATION - BASICS
The controller should be installed in a place protected against adverse
environmental conditions, protected from third party access - in the ush box
or inside the enclosure of the controlled device. Remember that metallic
elements (wires, housing parts) have a negative inuence on the range of the
device, and consequently the comfort of use. It is recommended that the
device be mounted in a stable and xed position.
Read the diagram and then proceed to install the controller. Pay particular
attention to the designation of the controller connectors. Start by connecting
the + 12V / + 24V power wires (red or black with a white dotted line) and GND
(black).
Paying attention to the polarity, connect the inputs controlling the engine
control panel. Depending on the control panel, will be necessary to connect
one or two inputs. The controller output O1 is destined for control in the open
/ stop / close mode. The O2 output is an auxiliary output, applicable in the
control panel requiring a connection stop circuit when the motor works, or
may be used as an additional function, e.g. "wicket" if the control panel is
equipped with this functionality.
control with μWiFi technology
from any place in the World
CONNECTION DIAGRAM
If the motor has electromechanical limits switch, it is possible to receive
feedback from the controller, indicating the position of the motor in the
positions "Open" (intermediate position) "Closed". To do this, connect one of
the pins IN1 of the controller to the connector of the motor control panel
which indicates the closed position of the motor (usually FTC, SWC, FC) on the
other hand the second of the pins should be connected to the corresponding
common signaling. One of the IN2 input pins should be connected to the
connector indicating the open position of the motor (usually FCO, SWO, FA),
while the other one should be connected to the corresponding common
signaling. The connection polarity of the controller inputs is not signicant.
IN1
5 - 24V
IN2
12-24V
AC/DC
PWR
O2
made in
Europe
O1
12 - 24V
S1 S2
push-button
It is necessary to connect the right pin of the given output
(O1 / O2) so that it has a higher potential than the left pin.
In case of an inverted connection, due to the internal
construction, it will connect the output which may cause
the movement of the motor even without control it. In this
situation, it is necessary to reverse the pair of wires
connected inside output.
Pay attention to the maximum output current
capacity - the control current cannot exceed 20mA
per output. Overloading the output will cause
irreparable damage to the controller.
Information advanced for installers in relation to the
output polarity, when is connected to engines control
panels for which the scheme is not available.
Specyfikacje produktu
| Marka: | Blebox |
| Kategoria: | Niesklasyfikowane |
| Model: | gateBox |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Blebox gateBox, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Blebox
1 Października 2024
1 Października 2024
1 Października 2024
Instrukcje Niesklasyfikowane
- Rösle
- Mobicool
- San Jamar
- Plantronics
- Multimetrix
- DigitSole
- Amiko
- Envivo
- Zenza Bronica
- JIMMY
- GFM
- Meister Craft
- Supermicro
- Lockwood
- Bikemate
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025