Instrukcja obsługi Boss Waza Craft DM-2W
Boss
Niesklasyfikowane
Waza Craft DM-2W
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss Waza Craft DM-2W (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 28 osób i została oceniona przez 14.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/1
Owner’s Manual
Precautions When Connecting
5
To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
5
Once the connections have been completed, turn on power to
your various devices in the order specied. By turning on devices
in the wrong order, you risk causing malfunction and/or damage
to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
5
Due to the characteristics of its analog circuitry, this unit’s CHECK
indicator may be lit (eect on) or unlit (eect o) when you turn
the power on.
Use of Battery
5
A battery was installed in the unit before it left the factory. The life
of this battery may be limited, however, since its primary purpose
was to enable testing.
5
If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (supplied on a separate sheet).
5
When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
5
Batteries should always be installed or replaced before connecting
any other devices. This way, you can prevent malfunction and
damage.
5
If the battery runs extremely low, the sound may distort or
the delay time may be shortened, but this does not indicate a
malfunction. If this occurs, please replace the battery.
OUTPUT/DIRECT OUT jacks
Connect to only the OUTPUT jack
DM-2W
The direct sound + delay sound is output.
Connect to the OUTPUT jack and the DIRECT OUT jack
DM-2W
Direct soundDelay sound
The delay sound is output from the OUTPUT jack, and the direct sound is
output from the DIRECT OUT jack.
Connect to the SEND/RETURN jacks of a guitar amplier
DM-2W
RETURN
Dummy plug
SEND
INPUT
If you’re using this unit in a parallel-connected eect loop, insert a dummy
plug into the DIRECT OUT jack so that only the delay sound is output to
the RETURN jack.
Caution When Using the RATE Jack
5
Use only the specied expression pedal (Roland EV-5; sold
separately). By connecting any other expression pedals, you risk
causing malfunction and/or damage to the unit.
5
Use the minimum volume of the EV-5 to specify the maximum
delay time, and use the REPEAT RATE knob of the DM-2W to
specify the way in which the delay time will change (i.e., the curve
of change).
Some settings of these knobs might not produce the correct
eect. Listen to the sound while you adjust the minimum volume
and the REPEAT RATE knob.
5
Depending on the setting of the INTENSITY knob, oscillation may
occur while you operate the pedal, causing the volume to increase
suddenly. Take care to avoid damaging the connected guitar amp
or speaker.
Changing the Battery
1. Hold down the pedal and
loosen the thumbscrew ,
then open the pedal upward.
* The pedal can be opened without
detaching the thumbscrew completely.
2. Remove the old battery from
the battery housing , and
remove the battery snap
connected to it.
3. Connect the battery snap to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the
back of the pedal, and then close the pedal.
* Carefully avoid getting the battery snap cord caught in the
pedal, coil spring, and battery housing.
5. Insert the thumbscrew into the guide bush hole and
tighten it securely.
Specications
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output
Level
-20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance
10 kΩ or greater
Power Supply Alkaline battery (9 V, 6LR61) (9 V, 6F22) or
Carbon-zinc battery
AC adaptor (PSA series: sold separately)
Current Draw 35 mA
* Expected battery life under continuous use:
Alkaline: 15 hours
Carbon: 5 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 460 g / 1lb 1 oz (including battery)
Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT
NOTES,” and “Information”)
Alkaline battery (9 V, 6LR61)
Options
(sold separately)
AC adaptor (PSA-series)
Expression pedal: Roland EV-5
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
9 V Battery
English
Main Features
Panel Descriptions
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
7This is a “WAZA CRAFT series” eect unit featuring analog circuitry painstakingly designed in every detail for the best possible sound.
7This is a painstakingly designed analog delay using carefully selected BBD components.
7In addition to the sound of the original DM-2, you’ll enjoy a custom tone that’s been fully tuned-up by BOSS engineers.
INPUT jack
This jack accepts signals coming from
a guitar or other musical instrument, or
another eects unit.
* The INPUT jack doubles as the power switch.
Power to the unit is turned on when you plug into the
INPUT jack; the power is turned o when the cable is
unplugged.
To prevent unnecessary battery consumption, be sure
to disconnect the plug from the INPUT jack when not
using the eects unit.
AC Adaptor
(PSA series: optional)
Electric Guitar
Guitar Amplier
REPEAT RATE knob
Adjusts the delay time. Turning the knob toward the right shortens the delay
time.
* Delay time (maximum)
S (standard): 300 ms, C (custom): 800 ms
DIRECT OUT jack
Only the direct sound is output from this
jack.
Guitar Amplier
RATE jack
If you connect an expression pedal (Roland EV-5) to this
jack, you can use it to control the delay time.
* Refer to “Caution When Using the RATE Jack.”
Roland EV-5
DC IN jack
Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without
being concerned about how much battery power you have left.
* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the correct
voltage. Do not use any other AC adaptor, since this may cause malfunction.
* If the AC adaptor is connected while a battery is installed, the power supply
is drawn from the AC adaptor.
* We recommend that you keep batteries installed in the unit even though
you’ll be powering it with the AC adaptor. That way, you’ll be able to
continue a performance even if the cord of the AC adaptor gets accidently
disconnected from the unit.
CHECK indicator
This indicator shows whether the eect is on or o, and also doubles as the battery check
indicator. The indicator lights when the eect is on.
* If you’re powering the unit with a battery and the CHECK indicator goes dim— or doesn’t
light at all—when you try to turn the eect on, the battery is near depletion and should be
replaced. For instructions on changing the battery, refer to “Changing the Battery.”
OUTPUT jack
The direct sound and delay sound are
mixed and output from this jack.
If a plug is inserted in the DIRECT OUT
jack, only the delay sound is output from
this jack.
Pedal switch
This switch turns the eect on/o.
Thumbscrew
When this screw is loosened, the
pedal will open, allowing you to
change the battery.
* For instructions on changing
the battery, refer to “Changing
the Battery.”
ECHO knob
Adjusts the volume of the delay sound. Turning the knob toward the right makes
the delay sound louder. If you turn the knob all the way to the left, only the
direct sound is heard.
INTENSITY knob
Adjusts the number of delay repeats. Turn this knob toward the right to increase
the number of repeats. If you turn the knob all the way to the left, a single delay
is heard.
* If you turn the knob all the way to the right, oscillation might occur.
Mode switch
Switches the tonal character.
S (standard) The original tone of the DM-2.
C (custom) A clear, customized tone with an extended delay time.
03
© 2014 Roland Corporation
Specyfikacje produktu
| Marka: | Boss |
| Kategoria: | Niesklasyfikowane |
| Model: | Waza Craft DM-2W |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Boss Waza Craft DM-2W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Boss
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
Instrukcje Niesklasyfikowane
- JAR Systems
- Traeger
- Pure 100
- Dolmar
- Zibro
- Guardian
- Giardino
- Brizo
- Seagate
- Sound Devices
- Nest
- BOYA
- Reflecta
- Dreambaby
- Testo
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025