Instrukcja obsługi Boss Distortion DS-1X
Boss
Niesklasyfikowane
Distortion DS-1X
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss Distortion DS-1X (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 30 osób i została oceniona przez 15.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/1
Owner’s Manual
Precautions When Connecting
5
If you’ll be using the DS-1X for an extended time, we recommend
that you use an AC adaptor. If you prefer to use a battery, we
recommend an alkaline battery.
5
To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
5
Once the connections have been completed, turn on power to
your various devices in the order specied. By turning on devices
in the wrong order, you risk causing malfunction and/or damage
to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
5
Before turning the unit on/o, always be sure to turn the volume
down. Even with the volume turned down, you might hear some
sound when switching the unit on/o. However, this is normal and
does not indicate a malfunction.
Changing the Battery
1. Hold down the pedal and loosen the thumbscrew, then
open the pedal upward.
* The pedal can be opened without detaching the thumbscrew
completely.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
2. Remove the old battery from the battery housing, and
remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil
spring, and battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Specications
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output
Level
-20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance
10 kΩ or greater
Power Supply Alkaline battery (9 V, 6LR61)
AC adaptor (PSA series: sold separately)
Current Draw 60 mA
* Expected battery life under continuous use:
Alkaline: 6 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 440 g / 1 lb (including battery)
Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT
NOTES,” and “Information”)
Alkaline battery (9 V, 6LR61)
Options
(sold separately)
AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
Panel Descriptions
English
7This is a cutting-edge distortion eect that is distinctly dierent than previous types of distortion.
7The DS-1X adds the perfect amount of distortion for each frequency region without requiring you to adjust the settings, seamlessly providing the ideal distortionwhether you’re ring on low notes or
playing a lead solo on high notes.
7You’ll be able to adjust your tone easily and intuitively.
Main Features
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
AC Adaptor Jack
Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without
being concerned about how much battery power you have left.
* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the
correct voltage. Do not use any other AC adaptor, since this may cause
malfunction.
* If the AC adaptor is connected while power is on, the power supply is
drawn from the AC adaptor.
* We recommend that you keep batteries installed in the unit even though
you’ll be powering it with the AC adaptor. That way, you’ll be able to
continue a performance even if the cord of the AC adaptor gets accidently
disconnected from the unit.
CHECK Indicator
Shows whether the eect is on or o, and also doubles as the battery check indicator. The
indicator lights when the eect is on.
* If you’re powering the unit with a battery and the CHECK indicator goes dim— or
doesn’t light at all—when you try to turn the eect on, the battery is near
depletion and should be replaced. For instructions on changing the battery, refer
to “Changing the Battery.”
Pedal Switch
This switch turns the eect on/o.
Thumbscrew
When this screw is loosened, the pedal will
open, allowing you to change the battery.
* For instructions on changing the
battery, refer to “Changing the Battery.”
INPUT Jack
Accepts signals coming from a guitar or other musical instrument, or another
eects unit.
* The INPUT jack doubles as the power switch. Power to the unit is turned on
when you plug into the INPUT jack; the power is turned o when the cable
is unplugged. To prevent unnecessary battery consumption, be sure to
disconnect the plug from the INPUT jack when not using the eects unit.
OUTPUT Jack
Connect this jack to your amp or to the input of another eect unit.
AC Adaptor
(PSA series: optional)
Electric Guitar
Guitar Amplier
LEVEL Knob
Adjusts the volume when the eect is on.
LOW Knob
Adjusts the tone quality of the lower range when the eect is on.
HIGH Knob
Adjusts the tone quality of the upper range when the eect is on.
DIST Knob
Adjusts the amount of distortion applied to the sound. Turning the knob
clockwise boosts the distortion eect.
Use of Battery
5
A battery was installed in the unit before it left the factory. The life
of this battery may be limited, however, since its primary purpose
was to enable testing.
5
If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (supplied on a separate sheet).
5
When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
5
Batteries should always be installed or replaced before connecting
any other devices. This way, you can prevent malfunction and
damage.
© 2014 Roland Corporation
02
Specyfikacje produktu
| Marka: | Boss |
| Kategoria: | Niesklasyfikowane |
| Model: | Distortion DS-1X |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Boss Distortion DS-1X, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Boss
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
Instrukcje Niesklasyfikowane
- Maruyama
- Radiant
- Thermalright
- Dnt
- One For All
- Denver
- Alba
- Gravity
- Zipper
- Tempo
- Pelco
- Goodram
- MEPROLIGHT
- Austrian Audio
- AXA
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025