Instrukcja obsługi Boss Bass Equalizer GEB-7
Boss
Niesklasyfikowane
Bass Equalizer GEB-7
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss Bass Equalizer GEB-7 (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 4.5 użytkowników na średnio 4.6 gwiazdek
Strona 1/1
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
AC Adaptor
(PSA series; sold separately)
Electric Bass
English
Equalizer Control knobs
These knobs allow you to boost or cut the center frequency of 50, 120, 400,
500, 800, 4.5 k or 10 kHz within +/-15 dB.
The BOSS GEB-7 is a 7-band equalizer designed specically for electric bass.
Since it allows for a broad range of frequency settings, even ve string basses can be accommodated.
The unit is designed to provide the optimum Q (equalizer’s bandwidth) for bass for each center frequency. While making it easy to obtain the most delicate of nuances, it also allows for radically unique settings as well.
The GEB-7 allows you to adjust the output level of the equalized sound so it matches the level of the input sound.
OUTPUT jack
Connect an amplier to this jack.
Bass Amplier
DC IN jack
Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play
without being concerned about how much battery power you have left.
* We recommend that you keep batteries installed in the unit even though you’ll be powering it
with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the
AC adaptor gets accidentally disconnected from the unit.
* Use only the specied AC adaptor (PSA-series).
CHECK indicator
This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.
The indicator lights when an eect is ON.
* If this indicator goes dim or no longer lights while an eect is ON, the battery is near
exhaustion and should be replaced immediately.
* The CHECK indicator shows whether the eect is on or o, and indicates the dierent
functions. It does not indicate whether the power to the device is on or not.
Pedal Switch
This switch turns the eects ON/OFF.
Thumbscrew
When this screw is loosened, the pedal will open, allowing you to change the
battery.
* For instructions on changing the battery, refer to “Changing the
Battery.”
Panel Descriptions
Main Features
Operating the Unit
1. When you have made the necessary
connections, set the knobs as shown
in the illustration.
2. Depress the pedal switch to turn the
eect on. (Make sure that the CHECK
Indicator lights.)
3. Adjust the tone using the relevant
Equalizer Control Knobs.
4. Adjust the output level using the
Level Control Knob, to minimize the
level dierence between the eect
and direct sounds.
FREQUENCY RESPONSE
k01k1001
FREQUENCY
(
Hz
)
-15
0
+
15
LEVEL (dB )
10
Use of Battery
* A battery is supplied with the unit. The life of this battery may
be limited, however, since its primary purpose was to enable
testing.
* If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY”
and “IMPORTANT NOTES” (supplied on a separate sheet).
* When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
* Batteries should always be installed or replaced before
connecting any other devices. This way, you can prevent
malfunction and damage.
Changing the Battery
1. Hold down the
pedal and loosen
the thumbscrew,
then open the
pedal upward.
* The pedal can be
opened without
detaching the
thumbscrew
completely.
2. Remove the old
battery from the
battery housing,
and remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil spring, and
battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Main Specications
BOSS GEB-7: Bass Equalizer
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance
10 kΩ or greater
Power Supply
DC 9 V; Dry battery 6F22 (9 V) type (carbon)/Dry
battery 6LR61 (9 V) type (alkaline) AC Adaptor
(PSA-series: optional)
Current Draw 16 mA (DC 9 V)
* Expected battery life under continuous use:
Carbon: 16 hours, Alkaline: 28.5 hours
These gures will vary depending on the
actual conditions of use.
Dimensions
73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight
440 g / 1 lb (including battery)
Accessories
Owner’s Manual, Leaet (“USING THE UNIT
SAFELY,” “IMPORTANT NOTES,” and “Information”),
Dry battery/9 V type (6F22)
Options
AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
Copyright © 2017 ROLAND CORPORATION
* To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units before making
any connections.
* Before turning the unit on/o, always be sure to turn the volume down. Even with the volume turned down, you
might hear some sound when switching the unit on/o. However, this is normal and does not indicate a malfunction.
* Once everything is properly connected, be sure to follow the procedure below to turn on their power. If you turn on
equipment in the wrong order, you risk causing malfunction or equipment failure.
: When powering up Turn on the power to your bass amp .last
: When powering down Turn o the power to your bass amp .rst
Level Control Knob
This knob allows you to adjust the output level of the eect sound to minimize
the level dierence between the eect and direct sounds.
Setting Samples
Standard Rock Heavy Metal Slapping Play
Bass Amplier Simulation
Owner’s Manual
INPUT jack
This jack accepts input signals (coming from a bass guitar, some other musical
instrument, or another eects unit).
* The INPUT jack also serves as the power
switch. Power is turned on whenever a plug
is inserted into the INPUT jack, and is turned
o when the plug is disconnected. When
not using the unit, you should disconnect
any cord connected to the INPUT jack.
* 5 1 0 0 0 5 5 1 6 5 - 0 1 *
Specyfikacje produktu
| Marka: | Boss |
| Kategoria: | Niesklasyfikowane |
| Model: | Bass Equalizer GEB-7 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Boss Bass Equalizer GEB-7, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Boss
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
Instrukcje Niesklasyfikowane
- Excalibur
- Tot Tutors
- Arylic
- Balay
- Venom
- Peach
- Sencor
- Yli Electronic
- Eligent
- Weston
- Auto XS
- Barska
- Globo
- Zotac
- Nexcom
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025