Instrukcja obsługi Chamberlain 050ACTWFATS

Chamberlain Niesklasyfikowane 050ACTWFATS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chamberlain 050ACTWFATS (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 27 osób i została oceniona przez 14 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/12

To insert or

remove the wires

from the terminal,

push in the tab with

a screwdriver tip.

Red

White

Grey

White

DANGER PELIGRO

132C2280-3D

TO ERAS E ALL

RECEIVER CODES

1. Pres s an d HOLD

rece iver orange

ERASE butto n

6 se conds . Indica tor

light will turn O N.

2. Relea se b utton when light tu rns O FF .

CANADA:

PART NO.: NO. DE PIEZ A:

DATE:

TH E CHAMB ER LAIN

GR OUP, I NC., US A

Ens ambla do en Méxi co

As sem bled i n Mexico

ELIMINACIÓN DE

TODOS LOS CÓDIGOS DEL

RECEPTOR

1. MANT ENGA PRESIONAD O

el b otón n aranja "ERASE"

del receptor d urante 6

se gund os. La lu z d el

indicador se encenderá.

2. Suelte el botó n cuan do la

luz se apague.

DANGER PEL IGRO

132C2280-3D

TO ERASE AL L

RECE IVE R C ODE S

1. Press and H OLDreceiver orang e

ERASE butt o n

6 second s. In d i cato r

ligh t wi ll t u rn O N.

2. Release bu tt o n when li g h t tu rns OFF .

CAN ADA:

P : PIEZA:ARTN O. N O.DE

DATE:

TH E CH AMBERLAIN GROU IN C., USAP,

Ensamblado en M éxi co

Assembled i n M exi co

ELIM INA CIÓ N DE

TODOSL OS CÓDIG OS D EL

RECE PTOR

1. MANTENGAPRESION ADOel bo t ón n aran ja "ER ASE"

del recept o r d u ran t e 6

segun d o s. La lu z d el

ind i cado r se en cend erá.

2. Suelte el b ot ón cu an d o l a

luz se apag u e.

Before you begin

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Model 050ACTWFATS

1.2 To maintain your warranty, place the

provided label over the existing label

on the end panel of the door operator.

Place the STEP SAVER SETUP label on

the end panel directly below the yellow

LEARN button.

1.1 Remove the light lens by pulling the

top sides of the light lens and rotate the

light lens down. Squeeze the light lens

clips to remove lens from end panel.

Your new myQ® serial number is located on the replacement label with your replacement logic board. You will need this new myQ ® serial number to connect your operator to the network. You will also

have a STEP SAVER SETUP label that must be adhered to your end panel directly under the yellow LEARN button for future identification. This second label indicates your board has been updated, and a

new Product Label should be placed over the current Product Label. Your product may look different.

1.3 Disconnect power to the door operator.

Remove the receiver logic board

2.1 Disconnect the wires from the quick-connect terminals ( ). A

Remove the receiver logic board end panel from the door

operator.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers to remove

the harnesses.

To prevent possible SERIOUS INJURY or

DEATH:

• Disconnect ALL electric and battery