Instrukcja obsługi Chamberlain 45ACT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chamberlain 45ACT (13 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 8 użytkowników na średnio 4.8 gwiazdek

1

DANGER s PELIGRO

132C2280-3D

TO ERASE ALL

RECEIVER CODES

1. Pre ss and HOLD

re ce iver or ange

ERASE butt on

6 se conds. Indica tor

light will t urn ON.

2. Rele ase butt on

whe n light turns OFF.

CANADA:

PART NO.:NO. DE PIEZ A:

DATE:

T HE CHAMB ERLAIN

GRO UP, IN C., US A

Ens am blad o e n Méxi co

Ass em bled in Me xico

ELIMINACIÓN DE

TODOS LOS CÓDIGOS DEL

RECEPTOR

1. MANTENGA PRESIONADO

e l botón nar anja "ERASE"

de l rece pto r dura nte 6

se gundos. La luz de l

indica dor s e e nce nderá.

2. Sue lte el botón cua ndo la

luz se apa gue.

DANGER s PELIGRO

132C2280-3D

TO ERASE ALL

RECEIV ER CODE S

1. Press and HOL D

receiver orange

ERASE bu tton

6 secon ds. In dicato rlig h t wi ll tu rn ON.

2. Release bu tton

when ligh t tu rns OF F.

CANADA:

PART NO.:N O. DE PIEZA:

DATE:

THE C HA MB ERLA IN

GROU P, I NC. , U SA

Ensamblado en México

Assembled in Mexico

ELIM INAC IÓN DE

TODOS LOS C ÓDIGOS DEL

RECEP TOR

1. MANTENGAPRE SION ADO

el b otón naranja "ERASE "

d el receptor durante 6 segundos. L a lu z d el

ind i cador se encenderá.

2. Suelte el bo t ó n cuando l a

luz se apagu e.

Before you begin

1

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Model 45ACT

1.2 To maintain your warranty, place the

provided label over the existing label on

the end panel of the garage door opener.

1.1 Remove the light lens by pulling the top

sides of the light lens and rotate the light

lens down. Squeeze the light lens clips to

remove lens from end panel.

NOTE: The products illustrated in the instructions are for reference. Your product may look different.

1.3 Disconnect power to the garage door

opener.

Remove the receiver logic board

2

2.1 Disconnect the wires from the quick-connect terminals (). A

Remove the receiver logic board end panel from the garage

door opener.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers, to

remove the harnesses.

2.3 Remove the receiver

logic board from the

end panel by removing

the 2 screws and

releasing the 2 clips.

To prevent possible SERIOUS INJURY or

DEATH:

• Disconnect ALL electric and battery

power BEFORE performing ANY service

or maintenance.

To prevent damage to the receiver/logic

board, DO NOT touch printed circuit board

of replacement receiver/logic board during

installation.

ALWAYS wear protective gloves and eye

protection when changing the battery or

working around the battery compartment.

Screws

Clips

A

To insert or remove

the wires from the

terminal, push in the

tab with a

screwdriver tip.

Red

White

White

Grey

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth

defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Specyfikacje produktu