Instrukcja obsługi Cocraft DV2011B
Cocraft
Niesklasyfikowane
DV2011B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cocraft DV2011B (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.4 gwiazdek
Strona 1/4
GREAT BRITAIN
For consumer contact, please visit www.clasohlson.co.uk
and click on customer service.
Stud Detector
Art.no 40-8158 Model DV2011B
Please read the entire instruction manual before using the product and save it
for future reference. We reserve the right for any errors in text or images and
any necessary changes made to technical data. If you have any questions
regarding technical problems please contact our customer services.
Safety
Be when hammering in nails, or when sawing or drilling into a wall, CAREFUL
oor or ceiling where there is a possibility of striking live wires, pipes, etc.
The normal distance between centres of studs is 16 or 24 (40 or 60 cm) ″ ″
and they are normally 1 2 (25–50 mm) in width. If you receive readings that – ″
deviate from this standard, you should investigate before proceeding. Always
turn off the mains electricity before beginning to drill, saw or nail near cables.
Product description
Multi-detector used for nding metal pipes, live electrical wires and joists/
battens. LCD display with indication segments and an audible signal which
assist in object detection. The user can choose one of four manual operation
modes, each with an audible detection signal.
Getting started
Inserting the battery
1. Remove the battery cover.
2. Connect a 9 V battery to the battery wires.
3. Make sure that the battery wires are not crushed when inserting the battery.
4. Ret the battery cover.
Buttons and functions
Display
3. Mark where the edge is and then continue scanning the stud. past
Work your way back towards the stud from the other side and locate and
mark the other edge of the stud. The centre of the stud is halfway between
the two marks.
1. Live wire symbol.
2. STUD: Scan for wooden battens.
3. METAL: Scan for metal.
4. DEEP: Scan for wooden battens
hidden deeper.
5. AC: Scan for live electrical wiring.
6. Location indicator with several segments.
Operation
Calibration
Note: The stud detector automatically recalibrates every time the button on
the side is pressed.
1. Hold the detector steady against the surface to be scanned.
2. Press [ ] to turn on the stud detector.
3. Press [ ] to set the desired mode: STUD – METAL – DEEP – AC.
4. Depress the button on the side of the stud detector. When the detector
has been calibrated, three short audible signals will be emitted.
Note: The stud detector must be kept still during calibration.
Note: Depress the button on the side the entire time during calibration and scanning.
Scanning for metal
1. Calibrate the detector as described above.
2. Move the detector both horizontally and vertically over the surface
being scanned.
3. When a metal object is detected, an audible signal will be emitted and
the location indicator will be shown on the display. When all segments
show on the display, a metal object has been found.
4. Turn off the alarm by pressing [ ]. If the stud detector is not turned off
manually it turns off automatically after one minute to save power.
Scanning for studs
1. Calibrate the detector as described above.
2. Move the stud detector in one direction over the surface being scanned.
When the detector gets close to a stud an audible signal will be emitted
4. Turn off the alarm by
pressing [ ]. If the stud
detector is not turned off
manually it turns of
automatically after one
minute to save power.
Deep stud scan (up to 38 mm)
1. Calibrate the detector as described above.
2. Move the stud detector in one direction over the surface being scanned.
When the detector gets close to a stud an audible signal will be emitted
and the side segments of the location indicator will appear on the display.
When all of the segments have appeared the arrow on the display will
point at the edge of the stud.
3. Mark where the edge is and then continue scanning past the stud. Scan
back towards your mark to locate the other edge of the stud and then make
another mark. The centre of the stud is halfway between these two marks.
4. Turn off the alarm by pressing [ ]. If the stud detector is not turned off
manually it turns off automatically after one minute to save power.
Scanning for electrical wiring (AC)
1. Calibrate the detector as described above.
2. Move the detector over the area to be scanned.
3. When the detector gets close to a live electrical wire, an audible signal will
be heard and the side segments of the location indicator will appear on
the display. The live wire symbol will also appear. When all segments are
shown on the display, the arrow in the middle will point to the live wire.
4. Turn off the alarm by pressing
[ ]. If the stud detector is not
turned off manually it turns off
automatically after one minute
to save power.
Troubleshooting guide
Problem: The detector beeps as soon as it is placed against the wall (surface).
1. Place the detector against the wall (surface) while it is turned . OFF
Press [ ] to turn on the stud detector.
2. Calibrate the detector as described above.
3. Once calibrated the detector can be moved sideways. The detector
beeps when it locates a stud which is thicker than the material in the wall
at the place of calibration.
4. If no studs are found, it might be because the detector was calibrated
directly over a stud, in that case repeat the calibration procedure at
another location.
5. Always check before scanning that the felt pads are pressed against
the surface to be scanned.
Disposal
When it is time to dispose of this product, do so in accordance with local
regulations. If you are unsure how to proceed, contact your local authority.
Specifications
Operating temperature -2 ºC to + 45 ºC
Max. air humidity 80 % RH
Max time for calibration 5 seconds
Battery 1 x 9 V (6F22)
If the battery power is low the detector automatically shuts off.
If the stud detector is left on for more than one minute it shuts off automatically.
Mode Max scan depth Accuracy
STUD 19 mm 3 mm
DEEP 38 mm 5 mm
METAL 50 mm 6 mm
AC 50 mm -
and the side segments of
location indicator will appear
on the display. When all of
the segments have appeared
the arrow on the display will
point at the edge of the stud.
6
1
2 3 4 5
Specyfikacje produktu
| Marka: | Cocraft |
| Kategoria: | Niesklasyfikowane |
| Model: | DV2011B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Cocraft DV2011B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Cocraft
20 Sierpnia 2024
20 Sierpnia 2024
20 Sierpnia 2024
20 Sierpnia 2024
20 Sierpnia 2024
14 Sierpnia 2024
Instrukcje Niesklasyfikowane
- Grace Design
- Hubble Connected
- Craftsman
- Nemef
- Chauvin Arnoux
- Greisinger
- Moomin
- SEADA
- ACME
- FontaFit
- ISi
- Cosori
- Ibm
- Zoofari
- Spacedec
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025