Instrukcja obsługi Dnipro DOT
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dnipro DOT (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 43 osób i została oceniona przez 22 użytkowników na średnio 4.3 gwiazdek
Strona 1/1
META
MODE
You can switch saved
patterns via CV.
Pres all 3 buttons
simultaneously to activate
META mode (all buttons will
start flashing rapidly).
In this mode you can quickly
switch between saved
patterns just with an encoder
turn, or by applying CV to CV
IN 1, while CV IN 2 and CV IN 3
will be reffered to a ratchet
function.
Note, when entering this
mode, your current pattern
will be saved to the native
slot, so you can use this as a
hot key for quick saving.
MENUes GLOBAL MENU OPTIONAL
MENU
Of course there are additional
tools and settings you can find
in two menus: Global menu
and .Optional menu
Press and hold encoder for a
second to enter Global menu
and navigate through 4 menu
pages. To exit Global menu ,
simply press encoder again.
Press and hold track button to
call for Optional menu. Rotate
encoder to navigate through
pages. Push encoder to apply
selected function to an active
track or press any button to
exit.
Each track has a dedicated
bi-polar CV input. The
destination of each CV input is
represented by 3 color bricks
on the bottom of screen,
referred to a specific track
parameter: Green is for , FILL
Red is for , Yellow is for LENGTH
OFFSET.
CV inputs accepts bi-polar
signals from -5 to +5 v,
or usual 0 to +5v.
Push referred button to init
pattern data of a referred track.
You must confirm erasing with
second press.
Select to enter ratchet page
and set ratchets for desired
Press green button to load or
red to save pattern. On next
page, rotate encoder and select
1 of 16 available slots. Hit lighted
button again to load/save all 3
tracks t from selected slot. o/
Press encoder to exit.
Record User pattern by
tapping track buttons. Hold
track button to clear.
Use buttons to mute tracks.
CV IN
SETTINGS
PAGE
LOAD/SAVE
INITIALIZE
TRACK RATCHET
Select to erase patterns steps.
Instead of Track Init this
function erase data in
dependence of a current
mode, f.e. X pattern will be XO
erased when DOT is in XOX
mode or Euclid pattern when
current mode is euclidean.
AND MORE...
It is possible to flip DOTs
interface upside down. To do
this, press and hold encoder
on startup. Release when
tracks are loaded.
Press top two buttons & Hold
simultaneously to enter swing
parameter page. Rotate
encoder and add groove to
your patterns.
You can link several dots by
using a dedicated link cable.
Linked slave module will use
clock and reset from a master,
until slaves clock and reset
inputs are unpatched. Patch
that inputs to set slave module
run independently.
Converts Euclid pattern to X XO
pattern on the active track for
further editing.
ERASE
EUCLID
TO XOX
CONVERT
MUTE
RECORD
SWING
EUCLID
MODE
Dot is a 3 channel trigger
sequencer with polymetric
capabilities.
Each of three paired columns
of leds represents a trigger
track, which can be a 16 step
max.
Each track has a dedicated
button, trigger output and cv
input. Clock and reset inputs
are common for all tracks. Select active track by pressing
a corresponding button, rotate
encoder to edit the track.
Each track consists of two
layered patterns: Euclid and
XOX, so there are two modes to
record and modify track data:
Euclidean mode XOX and
mode. Euclid pattern is shown
by green dots on display,
while XOX pattern is red.
In euclidean mode you can
generate an Euclid pattern
which is is based on
euclidean algorithm. There
are 3 parameters that can be
edited with encoder: FILL,
LENGTH and OFFSET. Press
track button several times to
switch parameters, indicated
by a buttons light color. Green
is for FILL, Red is for LENGTH,
Yellow is for OFFSET. Rotate
encoder to edit them. te, No
LENGTH and OFFSET
parameters both reffered to
XOX and Euclid patterns.
Patch the clock input with
pulse to start sequencer
running.
Patch any trigger output to a
module that accepts triggers.
Trigger
outputs
CV inputs
Track
buttons
TRACKS
1 3 2
1 3 2
FILL
LENGTH
OFFSET
シ
ー
ケ
ン
サ
ー
点
ポ
リ
リ
ズ
ム
USER GUIDE 3.0
DOT
Specyfikacje produktu
| Marka: | Dnipro |
| Kategoria: | Niesklasyfikowane |
| Model: | DOT |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Dnipro DOT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Dnipro
27 Września 2024
Instrukcje Niesklasyfikowane
- Alpine
- KeepOut
- Autel
- KidKraft
- Dreambaby
- Thermionic Culture
- Valore
- JAXY
- Oertli
- Kaiser Fototechnik
- Irritrol
- Edge
- Comar
- Waring Commercial
- Inverto
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025