Instrukcja obsługi Electro Harmonix Bass Micro Synth
Electro Harmonix
Niesklasyfikowane
Bass Micro Synth
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Bass Micro Synth (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 30 osób i została oceniona przez 15.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/3
BASS MICRO SYNTH
Analog Bass Synthesizer
Congratulations on your purchase of the Electro-Harmonix XO Bass Micro Synth! You have
purchased a very powerful tool for musical expression. Please take a few minutes to familiarize
yourself with the Bass Micro Synth’s controls and how they work
The XO can create many of the most popular analog lead synthesizer BASS MICRO SYNTH
textures at a fraction of the normal cost for such capabilities. Its four voices: GUITAR,
OCTAVE, SUB-OCTAVE, SQUARE WAVEand are completely independent and fully mixable.
The BASS MICRO SYNTH can modify these signals with envelope control for a variety of
“bowed” and “blown” sounds. In addition, a sophisticated swept filter control allows highly
variable frequency adjustments to be made to the signal. When combined, these controls offer
the user a creative capability that is virtually limitless.
PREAMP GAIN ADJUSTMENT The preamp gain in the Bass Micro Synth has been set at the
factory for use with a bass equipped with single-coil passive pickups. If you will be using
another instrument with higher or lower output, it may be necessary to readjust this setting. A
screwdriver or alignment tool with a tip width of no more than 1/16" is required. To access the
preamp gain adjustment, remove the bottom plate from the Bass Micro Synth. Look for the
small trim pot in the lower left corner of the circuit board, it is labeled TRIM1 GAIN TRIM.
Turning the trim pot clockwise will increase the preamp gain. Turning it counter-clockwise will
decrease preamp gain. Please do not touch any other components when the bottom plate is
removed or you risk damaging the circuit board or the components.
OPERATION -The Bass Micro Synth’s controls operate as described below. In all cases, high
numbered control settings increase the level of the given effect.
FOOTSWITCH and Status LED – The Footswitch selects either effect mode or True Bypass.
When the Status LED is lit, the Bass Micro Synthesizer is in effect mode. When the Status LED is
off, the Bass Micro Synth is in True Bypass mode.
TRIGGER Determines the input volume at which the – filter circuits will “turn on.” It does not
affect any other circuitry. If the TRIGGER is set too high, the filter may “stutter” due to
multiple triggering. This is especially true if chords are played. It is best to set the TRIGGER
at exactly the sensitivity needed for your playing.
WARNING:
Your
Bass Micro Synth
comes equipped with
an
Electro-Harmonix 9.6DC-200BI
power supply
(same as used by Boss & Ibanez 9.6 Volts DC 200mA). ™ ™
Use only the adaptor
supplied
. Using the wrong adapter can cause serious bodily injury. Using the wrong adapter
may also damage your unit and will void the warranty. In addition, do not use a daisy
chained supply with the Micro Synth. The Micro Synth must have its own power supply.
Specyfikacje produktu
| Marka: | Electro Harmonix |
| Kategoria: | Niesklasyfikowane |
| Model: | Bass Micro Synth |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Electro Harmonix Bass Micro Synth, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Electro Harmonix
1 Stycznia 2025
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
5 Grudnia 2024
7 Października 2024
7 Października 2024
7 Października 2024
5 Października 2024
Instrukcje Niesklasyfikowane
- Marantz
- Eldat
- Positive Grid
- Hex
- Ziggo
- Bricasti Design
- ASIWO
- Busch And Müller
- DayStar Filters
- 8BitDo
- Maxicool
- Sungale
- RetroSound
- Mermade
- Cambium Networks
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025