Instrukcja obsługi Electro Harmonix Blurst
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Blurst (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 11 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
BLURST
Modulat Filter ed
Congratulations on your purchase of the Electro-Harmonix Blurst. The Blurst
is an analog low pass filter controllable by either internal or external
modulation. Use the parameters of the pedal to create a variety of sweeping
filter effects, including sounds reminiscent of vintage synthesizers.
While a typical envelope filter’s modulation is controlled by your guitar’s
attack, the filter in the Blurst is modulated by an internal low frequency
oscillator (LFO), similar to a tremolo or phaser. When you add an expression
pedal or control voltage ( source to the Blurst, you have even greater CV)
control over either the LFO or the filter itself.
The Blurst all-analog signal path contains fourth-order low pass filter with ’s a
variable resonance. Basic modulation is controllable via a variable internal
LFO with a choice of three wave shapes The modulation (including the LFO .
itself) controlled digitally, allowing for tap-tempo (with three tap-divide is
options and expression pedal control of your choice of three selectable )
parameters. These features greatly expand the variety of filtered sounds you
can generate with the Blurst.
- USING THE BLURST -
Power the Blurst with the included 9-volt power supply. The left, yellow LED
puls in time the set modulation rate. Press the right footswitch es to BYPASS
to engage the effect; t orange status LED lights to indicate that the effect he
is engaged.
S the modulation rate with either the knob or a combination of the et RATE
TAP footswitch and the toggle switch, whichever was most TAP DIVIDE
recently used. Toggle the switch to vary the modulation shape SHAPE
between a triangle wave ( ) rising saw-tooth ( ) a falling saw-tooth, a or
( ). Turn the control to set the frequency range of the filter RANGE
modulat . The maximum range is set with the knob at 50% (or 12 ion RANGE
o clock as indicated by the center detent). As you turn the knob ’ RANGE
counterclockwise (towards ), the range gets smaller and simultaneously LO
shifts towards lower frequencies. When you turn the knob clockwise RANGE
(towards from the center detent, the range also gets small and shifts HI) er
to higher frequencies.
RESONANCE sets the resonance (or Q factor) of the filter and affects the ,
output level of the filtered sound. Set the knob to control the blend BLEND
of the dry and filtered signal The knob controls the output . VOLUME
volume.
When you plug an expression pedal or a suitable control voltage (CV) source
(such as an EHX 8-Step Program) into the jack, set the three-way EXP EXP
MODE switch to select which parameter the expression pedal CV source or
controls. In mode you control the modulation rate, with the toe RATE
equaling the knob, or, if tap-tempo is enabled, the heel equaling the RATE
current tap-tempo setting. In mode you control the frequency range RANGE
of the filter, with the toe equaling the knob. In mode the RANGE FILTER
expression pedal or CV source controls the cutoff frequency of the filter
directly. In this mode, the and controls will do nothing. RATE RANGE
- CONTROLS I/O JACKS, POWER - ,
BYPASS Footswitch & Orange Status LED The orange LED illuminate–s
when the effect is engaged The status LED glows brightly to signal that all .
operational voltages are satisfactory. Tap the footswitch to toggle between
effect on and off. When the effect is off, the pedal is in true bypass mode.
Yellow Filter Status LED – The yellow LED illuminates based on the
current cutoff frequency of the filter. In most cases it can be used as a visual
representation of the rate of the LFO modulating the filter. NOTE: at certain
settings depending upon the position of the RANGE knob the LED will — —
remain lit or will not light at all.
TAP Footswitch Use this footswitch to tap in a tempo for the LFO. –
VOLUME Knob in effect mode. – Sets the Blurst’s output volume
BLEND Knob Sets the mix between dry and wet (filtered) signal. –
RESONANCE Knob – Sets the resonance of the filter; also affects the
volume of the filtered signal.
RANGE Knob –S ation. ets the frequency range of the filter’s modul
Maximum range with the knob at 50%. Range gets smaller and centers
around lower frequencies as you bring the knob from 50% to minimum.
Range gets smaller and centers around higher frequencies as you bring the
knob from 50% to maximum.
RATE Knob – ntrols the speed of modulation. Co
Specyfikacje produktu
| Marka: | Electro Harmonix |
| Kategoria: | Niesklasyfikowane |
| Model: | Blurst |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Electro Harmonix Blurst, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Electro Harmonix
1 Stycznia 2025
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
5 Grudnia 2024
7 Października 2024
7 Października 2024
7 Października 2024
5 Października 2024
Instrukcje Niesklasyfikowane
- N8WERK
- ASIWO
- Klarstein
- Desview
- T4E
- Godox
- Metra
- Mobicool
- TFA
- VCM
- Humminbird
- Steiner
- Vemer
- Kessler
- Winia
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025