Instrukcja obsługi Electro Harmonix Nano Clone
Electro Harmonix
Niesklasyfikowane
Nano Clone
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Nano Clone (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 3.9 gwiazdek
Strona 1/1
NANO CLONE
Full Chorus
Congratulations on your purchase of the Electro Harmonix Nano Clone. The Nano
Clone is a compact battery operated Chorus device that features a RATE control
allowing you to change the speed of the Chorus.
To produce the Chorus effect, the Nano Clone bends the frequency slightly from the input
source and mixes this altered signal with some direct unaffected signal. The combination
produces a doubling effect.
- OPERATING INSTRUCTIONS -
Connect your instrument to the INPUT jack. Connect your amplifier to the AMP jack. Please
note that whenever a plug is inserted into the INPUT jack, the Nano Clone is ON and it is
draining current from the battery.
The RATE knob controls the speed of the chorus effect. Turning the RATE knob clockwise
increases the rate of the chorus.
The red LED will light up when the Nano Clone is in effect mode. When in True Bypass
mode, the LED will be off. Use the FOOTSWITCH to toggle between effect and True Bypass
mode.
- POWER -
Power from the internal 9-volt battery is activated by plugging into the INPUT jack. The input
cable should be removed when the unit is not in use to avoid running down the battery. If a
battery eliminator is used, the Nano Clone will be powered up as long as a wall-wart is
plugged into the wall.
The optional 9V power supply from Electro-Harmonix is
US96DC-200BI
(same as used by
Boss ™ & Ibanez™)
9.6 volts/DC 200ma.
The barrel connector on the front of the Nano
Clone is for the 9-volt battery eliminator capable of delivering 100 mA of current. The inner
ring of the 9-volt battery eliminator must be negative, the outer ring positive. The unit’s
battery may be left in or taken out when the eliminator is in use.
PLEASE NOTE:
If the Nano Clone is connected to other effects pedals it will not work with
the same battery eliminator that is daisy chained to the other pedals. The Nano Clone works
off of a negative power supply and therefore either needs its own battery eliminator or
should be run off the battery. If you do daisy chain your battery eliminator to the Nano
Clone, all of the pedals on that daisy chain will power down, including the Nano Clone. If this
happens, immediately remove the Nano Clone and give the Nano Clone its own power
supply, otherwise you risk damaging the Nano Clone, your other pedals or the battery
eliminator. Do not daisy chain the battery eliminator for the Nano Clone with any other
Electro-Harmonix pedals
except
for the EH Muff Overdrive pedal.
To change the 9-volt battery, you must remove the 4 screws on the bottom of the Nano
Clone. Once the screws are removed, you can take off the bottom plate and change the
battery. Please do not touch the circuit board while the bottom plate is off or you risk
damaging a component.
The input impedance presented at the Input Jack is 300 kohms. The output impedance at
the Output Jack is 600 ohms.
Specyfikacje produktu
| Marka: | Electro Harmonix |
| Kategoria: | Niesklasyfikowane |
| Model: | Nano Clone |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Electro Harmonix Nano Clone, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Electro Harmonix
1 Stycznia 2025
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
29 Grudnia 2024
5 Grudnia 2024
7 Października 2024
7 Października 2024
7 Października 2024
5 Października 2024
Instrukcje Niesklasyfikowane
- Avteq
- RYOBI
- Whitestone
- Improv
- Dormakaba
- Bicker Elektronik
- Procare
- Master
- Crofton
- Fritel
- Synamodec
- JVC
- WAYDOO
- Nanlite
- Cudy
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025