Instrukcja obsługi Eltako FJ62NP-230V
Eltako
Niesklasyfikowane
FJ62NP-230V
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Eltako FJ62NP-230V (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
Wireless shading element and
roller shutter actuator
FJ62NP-230V
GB
Temperature at mounting location:
-20°C up to +50°C.
Storage temperature: -25°C up to +70°C.
Relative humidity:
annual average value <75%.
30 200 535 - 3
Only skilled electricians may install this
electrical equipment otherwise there is
the risk of re or electric shock!
Wireless shading element and roller shutter
actuator 1+1 NO contact, 4 A/250 V AC, not
potential free, for a shading element motor
230 V AC. Standby loss only 0.6 watt.
For installation. 49x51 mm, 20 mm deep.
The terminals are plug-in terminals for
conductor cross-sections of 0.2 mm
2
to
2.5 mm
2
.
The convenient wireless technology permits
the teach-in of up to 32 wireless universal
pushbuttons, wireless direction pushbuttons
and wireless central control pushbuttons.
Zero passage switching.
Bidirectional wireless switchable.
Supply voltage, switching voltage and
control voltage local 230 V.
If supply voltage fails, the device is
switched off in de ned mode.
In addition to the wireless control input via
an internal antenna, this wireless actuator
can also be controlled locally by a conven-
tional control switch if tted previously.
Control is either by separate local control
inputs for Up and Down as direction push-
buttons or these two inputs are bridged and
controlled by single pushbuttons as universal
pushbuttons. A change in direction then
takes place by interrupting activation.
An incandescent lamp current is not per-
mitted.
valid for devices from production week
14/22 (see bottom side of housing)
Wireless pushbuttons can be taught in with
either the functions 'Up-Stop-Down-Stop'
as universal pushbuttons or as local push-
buttons as well as a wireless pushbutton or
roller shutter double pushbuttons can be
taught in as direction pushbuttons with press
top for 'Up' and bottom for 'Down'. Press
brie y to stop the movement. In addition,
the central control button can be taught in
with static priority.
The static priority is only active as long as
the radio button is pressed. With a control
signal, e.g. B. a radio transmitter module
FSM61 with switches that has been taught-in
as a central control button, the switching
position'Up' or 'Down' and the priority are
speci cally activated. With priority because
these control signals cannot be overridden
by other control signals until the central
command is canceled again by the end of
the control signal.
The tap reverse function can be activated:
universal pushbuttons, direction pushbuttons
and wired pushbuttons are intially in static
mode so that the position of the blind can
be adjusted.
With control via GFVS software, operating
commands for 'up' and 'down' with the exact
travel time information can be started. As
the actuator reports the exact elapsed time
after each activity, even when driving was
triggered by a pushbutton, the position of
the shading is always displayed correctly in
the GFVS software. Upon reaching the end
positions above and below the position is
automatically synchronized.
When a wireless window contact is taught
in, a lockout protection is set up for open
windows or doors to disable the Central
Down and GFVS Down commands.
Typical connection
Startup:
After power supply is switched on, the
teach-in mode is activated automatically
for 2 minutes if the memory is empty
(as-delivered state) or if the teach-in
mode was not blocked. Teach-in standby
is alerted by a short 'Down, Stop' signal.
If no action occurs for 2 minutes, teach-in
mode ends automatically.
This is signalled by a short 'Down, Stop'.
Teaching-in sensors
Universal pushbutton: tap brie y 3 times;
Direction pushbutton: tap brie y 4 times;
Top part of direction pushbutton as 'Up'
and lower part as 'Down' and 'Stop' in each
case; direction pushbuttons are fully
taught in automatically when the top or
bottom part is pressed.
Central control pushbutton Up:
Tap brie y 5 times;
Central control pushbutton Down:
Tap brie y 6 times;
Window contact FTK, FTKB: (EEP
D5-00-01) as well as FTKE (EEP F6-10-00):
Close and open the window brie y 4 times;
(Close window -> open -> close -> open
->- close -> open -> close -> open)
Wireless window handle sensor FFG7B:
(EEP A5-14-09)
Wireless window/door contact FTKB-hg,
mTronic:
(EEP A5-14-0A)
Wireless window door contact FFGB-hg:
(EEP A5-14-01, -03, -0A)
Wireless window door contact eTronic:
(EEP A5-14-01)
Wireless timer FSU55D, FSU65D:
(EEP A5-38-08)
(EEP
A5 38 08)
ON command = Up, OFF command = Down
GFVS: (EEP A5-3F-7F)
Con rmation telegrams are switched on
and sent automatically at teaching-in of
the GFVS. It locks automatically the
teach-in mode.
After a sensor is taught in, it is con rmed
by a short 'Down, Stop'; the teach-in
mode is active for a further 2 minutes.
To avoid teach-in by accident, the
teach-in mode is blocked automatically
2 minutes after the last teach-in if a
universal or a direction pushbutton was
previously taught in. This is alerted by
two short 'Down, Stop' signals.
Encrypted and unencrypted sensors can
be taught in.
Teach in encrypted sensors:
1. Activate teach-in mode if necessary.
2. Activate sensor encryption within
2 minutes.
3. Then teach in the encrypted sensor as
described under 'Teach in sensors'.
With encrypted sensors, use the 'rolling
code', i.e. the code changes in each tele-
gram, both in the transmitter and in the
receiver.
If a sensor sends more than 50 telegrams
when the actuator is not active, the sensor
is no longer recognised when the actuator
is active and must be taught in again as
'encrypted sensor'. It is not necessary to
teach in the function again.
Block teach-in mode immediately:
Tap the pushbutton or an already taught-in
wireless pushbutton (but not a central
control pushbutton) 3 times brie y and
once long (>2 seconds). Lock is signalled
by two short 'Down, Stop' signals.
Unlock teach-in mode:
Tap the rocker, a cable-bound push button
or an already taught-in wireless push-
button (but not a central control button)
4 times brie y and once long (>2 seconds).
Teach-in mode is signalled by a short
'Down, Stop' signal.
Teach in con rmation telegrams from
other actuators:
Unlock simpli ed learning mode:
1. Tap an already taught-in wireless
pushbutton (not central control push-
Specyfikacje produktu
| Marka: | Eltako |
| Kategoria: | Niesklasyfikowane |
| Model: | FJ62NP-230V |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Eltako FJ62NP-230V, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Eltako
3 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
Instrukcje Niesklasyfikowane
- Crosley
- Bretford
- Netgear
- Master
- Cadel
- Marker
- TESLA Electronics
- Rocktrail
- Axler
- Musser
- WARN
- Polar
- Kenton
- Archos
- Elinchrom
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025