Instrukcja obsługi Eltako FMZ14

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Eltako FMZ14 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 9 użytkowników na średnio 4.7 gwiazdek

Multifunction time relay with10 functions,

1CO contact potential free10A/250V AC,

incandescent lamps 2000 watts*, with

DX technology. Bidirectional. Only 0.4 watt

standby loss.

Modular device for DIN-EN 60715 TH35

rail mounting.

1module =18mm wide, 58mm deep.

Connection to the Eltako-RS485 bus. Bus

cross wiring and power supply with jumper.

Wireless window contacts (FTK) and

window handles at opened

windows with

the function NO or NC can be taught-in.

Several FTK and (or) window handles

are linked to each other.If a direction

switch is taught-in, a function (e.g. TI)

can be started using the top switch

(START) and stopped with the bottom

switch (STOP).

Patented Eltako Duplex technology allows

youto switch normally potential free

contacts in zero passage switching when

230V A/C voltage 50Hz is switched.

This drastically reduces wear. To achieve

this, simply connectthe N conductor to

the terminal (N) and L toK(L). This

results in an additional standby

consumption of only 0.1watt.

If supply voltage fails, the two contacts

switch off. When power is restored,

contact1closes.

Tittibt05dd

GB

Only skilled electricians may install

this electrical equipment otherwise

there is the risk of fire or electric

shock!

Temperature at mounting location:

-20°C up to +50°C.

Storage temperature: -25°C up to +70°C.

Relative humidity:

annual average value <75%.

RS485 bus actuator

Multifunction time relay

FMZ14

30 014 009 -2

valid for devices from production week

40/17 (see bottom side of housing)

Typical connection

contact1closes.

Time setting between 0.5 second and

20 hours.

Function rotary switches

Teach-in takes place using the top and

middlerotary switchesand then the time

is set. T is the time base and xT the

multiplier.

The function is selected using the bottom

rotaryswitch:

RV= off delay

AV= operate delay

TI=

clock generator starting with impulse

TP= clock generator starting with pause

IA= impulse controlled operate delay

(e.g. automatic door opener)

EW= fleeting NO contact

AW= fleeting NC contact

ARV= operate and release delay

ON= Permanent ON

OFF= Permanent OFF

The LEDbelow the upper function rotary

switch performs during the teach-in

process

according to the operation man-

ual.

It shows control commands by short

flickering during operation.

* The maximum load can be used

starting at a delay time or clock cycle

of 5 minutes. The maximum load will

be reduced for shorter times as follows:

up to 2 seconds 15%, up to 2 minutes

30%, up to 5 minutes 60%.

Typical connection

Description of functions

t1t2t1t2

TI

Wireless

input

K(L)-2

t

t

ARV

Wireless

input

K(L)-2

t1 t2= 3s

IA

Wireless

input

K(L)-2

t

EW

Wireless

input

K(L)-2

Wireless

input

K(L)-2

AW

t

t1t2t1

TP

Wireless

input

K(L)-2

t

AV

Wireless

input

K(L)-2

Wireless

input

K(L)-2

t

RV

Teaching-in wireless sensors in wire-

less actuators

All sensors must be taught-in in the

actuators so that they can detect and

execute commands.

Specyfikacje produktu