Instrukcja obsługi ENTES MPR-60S-41


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla ENTES MPR-60S-41 (39 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.9 gwiazdek

Strona 1/39
ATTENTION : Consult the operating instructions before using the equipment.
If these precautions are not properly observed and carried out, it can cause physical accident
or damage to the equipment or the installation.
The manufacturer or the authorized seller is not responsible for the consequences
resulting from failure to comply with these precautions.
SAFETY PRECAUTIONS
This equipment has been manufactured and tested and it has left the factory in perfectly safe condition.
To preserve this and ensure safe operation of the equipment the user should comply with the instructions
which are mentioned in this manual.
Before installing, check that the operating and network voltages are the same!
Before carrying out any work on the equipment, check that it is disconnected from the electrical supply.
If the equipment is no longer completely safe to use, it should be taken out of service and
protected against any accidental use.
Operator Safety
Read the following recommendations carefully before installing and operating the equipment.
The equipment described in this manual is designed only to be used by trained personnel.
Maintenance work must be carried out only by qualified, authorised personnel.
Personnel must observe the usual safety procedures for safe operation and during any maintenance work.
Breakdown Precautions
If you suspect that the equipment may no longer be safe (e.g. because of transport or operational damage),
it must be taken out of service and protected against any accidental use.
The equipment should be handed over to authorised technicians for checking.
Cleaning Instructions
Disconnect the equipment from the electrical supply and only use a damp cloth to clean the external surfaces.
Do not use any abrasive materials or solvents. Do not allow any moisture to reach the connection terminals.
1
MPR60S/MPR60S-10/20/21/40/41
NETWORK ANALYSER
A2922b
ver.1.78
Important note for system connection
indicators indicate the existence of the three phases. (See Figure 1)
If
indicator (Phase sequence is not correct) is seen, you have to change any of the 2 phases before
proceeding. (L1 - L2, L2 - L3 or L1 - L3)
Figure 1: The existence of three phases on LCD.
Standards which are applied to the device:
EN 61000-6-2, EN 61000-6-4, EN 55016-2-1, EN 55016-2-3, EN 55011, EN 61000-3-2, EN 61000-3-3, EN 61010-1
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11


Specyfikacje produktu

Marka: ENTES
Kategoria: Niesklasyfikowane
Model: MPR-60S-41

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z ENTES MPR-60S-41, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane ENTES

ENTES

ENTES GKRC-22E Instrukcja

3 Stycznia 2025
ENTES

ENTES GKRC-21E Instrukcja

3 Stycznia 2025
ENTES

ENTES SER-YU Instrukcja

27 Grudnia 2024
ENTES

ENTES ERB-50 Instrukcja

8 Października 2024
ENTES

ENTES GEM-10SH Instrukcja

8 Października 2024
ENTES

ENTES RGSR-24S-OG Instrukcja

8 Października 2024
ENTES

ENTES RGSR-20S-OG Instrukcja

8 Października 2024
ENTES

ENTES RG3-15CL Instrukcja

8 Października 2024
ENTES

ENTES MPR-53S-96 Instrukcja

8 Października 2024
ENTES

ENTES MPR-47S-L Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025